Abstract:Fretting wear damage of high-strength titanium fasteners has caused a large number of disastrous accidents. Traditionally, it is believed that both high strength and excellent ductility can reduce fretting wear damage. However, whether strength and ductility are contradictory or not and their appropriate matching strategy under the external applied normal stress ( F w ) are still confusing problems. Here, by analyzing the subsurface-microstructure deformation mechanism of several samples containing various α precipitate features, for the first time, we design strategies to improve fretting damage resistance under different matching relation between F w and the tensile strength of materials ( R m ). It is found that when F w is greater than R m or F w is nearly equivalent to R m , the deformation mechanism mainly manifests as serious grain fragmentation of β and α GB constituents. Homogeneous deformation in large areas only reduces damage to a limited extent. It is crucial to improve the strength to resist cracking and wear, but it is of little significance to improve the ductility. However, when F w is far less than R m , coordinated deformation ability reflected by ductility plays a more important role. The deformation mechanism mainly manifests as localized deformation of β and α GB constituents (kinking induced by twinning and spheroidizing). A unique composite structure of nano-grained/lamellar layer and localized deformation transition layer reduces fretting damage by five times compared with a single nano-grained layer. Only when the strength is great enough, improving the plasticity can reduce wear. This study can provide a principle for designing fretting damage resistant alloys.

The role of normal force on the fretting corrosion behaviour of alloy 690 TT tube against 410 stainless steel plate in high temperature high pressure water

The effectiveness of protective layer in reducing fretting wear of Alloy 690TT tubes/ 405 stainless steel plates

Frequency induced fretting corrosion mechanism evolution of Alloy 690 exposed to simulated secondary water

Evolution of wear damage in 690 alloy tube mated with 405 stainless steel plate due to fretting conditions

Fretting wear-induced sudden loss of corrosion resistance in a corrosion-resistant Ni-based alloy

The formation and evolution of third body covered on 690 alloy tube during fretting in 285 °C air

The effect of NaCl concentration on impact-sliding fretting corrosion behavior of Inconel 690TT heat transfer tubes

Investigation on fretting wear mechanism of 316 stainless steel induced by Ni dissolution during pre-immersion corrosion in the liquid lead-bismuth eutectic (LBE)

CORROSION BEHAVIOR OF SUPER-AUSTENITIC STAINLESS STEEL AL-6XN IN SUPERCRITICAL WATER

Computational Analysis and Empirical Formula for Effect of Contact Pressure on Fretting Fatigue Life of 690 Alloy

Influence of Chloride Concentration on Fretting Wear Behavior of Inconel 600 Alloy

Effects of displacement amplitude and normal force on fretting wear behavior of zirconium alloy tube in simulated primary water of PWR

Electrochemical study on the fretting corrosion synergistic damage mechanism of Inconel 690 alloy in different dissolved oxygen solution

Experimental and Numerical Analysis on the Impact Wear Behavior of TP316H Steel

Experimental study on Tube-to-Tube reciprocating sliding wear behaviors of Inconel 690 heat transfer tubes

Understanding the Microstructure Evolution of Ni-Based Superalloy Within Two Different Fretting Wear Regimes in High Temperature High Pressure Water

Effects of salt spray duration on the fretting corrosion behavior of the Inconel 690 alloy tubes

Revealing fretting corrosion synergistic mechanism of 316 stainless steel in liquid lead-bismuth eutectic (LBE)

Effect of CrAlTiN Coating on Fretting Wear Behavior of Inconel 690 Alloy in Dry and Seawater Conditions

Subsurface deformation mechanism and the interplay relationship between strength-ductility and fretting wear resistance during fretting of a high-strength titanium alloy

Effect of frictional frequency on the subsurface evolution of 316L stainless steel in tribocorrosion and its influence on the synergistic effect between corrosion and wear