Abstract:The evolution of phase composition and mechanical properties and the formation of oxide layers on Fe40–xNiCoCrAlx (x = 5 and 10 at.%) alloys in long-term oxidation at 900 and 1000°C were studied. In the initial cast state, depending on the aluminum content and valence electron concentration, the alloys contain only an fcc solid solution (VEC = 8 e/a) or a mixture of fcc and bcc phases (VEC = = 7.75 e/a). Thin continuous oxide scales containing Cr2O3 and NiCr2O4 spinel formed on the surface of both alloys oxidized at 900°C for 50 h. A further increase in the annealing time to 100 h leads to the formation of aluminum oxide Al2O3 in the scale on the Fe30Ni25Co15Cr20Al10 alloy, having high protective properties. An increase in the oxidation temperature to 1000°C results in partial failure of the protective layer on the alloy with 10 at.% Al. Long-term holding at 900°C (100 h) + 1000°C (50 h) does not change the phase composition of the Fe35Ni25Co15Cr20Al5 alloy matrix, being indicative of its high thermal stability. In the two-phase Fe30Ni25Co15Cr20Al10 alloy, the quantitative ratio of solid solutions sharply changes: the amount of the bcc phase increases from 4 to 54 wt.% and its B2-type ordering is observed. The mechanical characteristics of the starting alloys and those after long-term high-temperature annealing were determined by automated indentation. The hardness (HIT) and elastic modulus (E) of the cast Fe35Ni25Co15Cr20Al5 alloy are equal to 2 and 147 GPa, respectively, and decrease to 1.8 and 106 GPa after a series of long-term annealing operations. The Fe30Ni25Co15Cr20Al10 alloy shows the opposite dependence: HIT increases from 2.5 in the initial state to 3.1 GPa after annealing and E decreases from 152 to 134 GPa. This indicates that the Fe30Ni25Co15Cr20Al10 alloy is promising as a high-temperature oxidation-resistant and creep-resistant material.

A Study of Gas-Saturated Layer After Oxidation of Alloy Ti6242S at 500 – 800°C

Thermal Oxidation Behaviour of Ti6Al7Nb and Ti6Al4V Alloys

Characterization of the Surface Oxygen-Diffusion Zone of the Thermally Oxidized Titanium

Surface Characterization of Thermally Oxidized Titanium Alloys

High-Temperature Oxidation Behavior of Ti6242S Ti-based Alloy

Non-Isothermal Oxidation Behavior and Mechanism of a High Temperature Near-α Titanium Alloy

Thermodynamic and microstructural study of Ti2AlNb oxides at 800 °C

Mechanism of Formation of Surface Protective Layer in Heat-Resistant HP40NbTu Alloys during High-Temperature Oxidation

High-Temperature Oxidation Properties and Microstructural Evolution of Nanostructure Fe-Cr-Al ODS Alloys

Non-Isothermal Oxidation Behaviors and Mechanisms of Ti-Al Intermetallic Compounds.

Isothermal short‐term oxidation behavior of MAR‐M246 nickel‐based superalloy at 800°C and 1000°C

Oxidation behavior of a nickel-based single crystal superalloy at 1100 °C under different oxygen concentration

Comparative Study On Oxidation Behavior Of Fe-5wt% Cr Alloy In Various Mixed Atmospheres At 900-1000 Degrees C

OXIDATION MECHANISM OF BINARY Ti-Al ALLOYS AT ELEVATED TEMPERATURE

Non-isothermal Oxidation Characteristic of Titanium-Aluminium Intermetallic Alloys

High temperature oxidation behavior of alumina-forming austenitic stainless steel

Comparative Study on Oxidation Behavior of Fe-5wt% Cr Alloy in Various Mixed Atmospheres at 900–1 000 °C

Microstructural evolution during exposure in air and oxidation behavior of a nickel-based superalloy

Revealing High-Temperature Oxidation and Tensile Behaviors along with Underlying Mechanisms of a Titanium Alloy with Precipitated Titanium Silicide

Structural State of High-Entropy Fe40–xNiCoCrAlx Alloys in High-Temperature Oxidation

A study on the high-temperature oxidation of ZM6 alloy through advanced characterization