Abstract:TiC + NiCrBSi binder metal matrix composites were obtained by self-propagating high-temperature synthesis (SHS) in the reaction powder mixtures of titanium, carbon (carbon black) and NiCrBSi alloy. It has been found that steady combustion in a stationary mode occurs when the content of the thermally inert metal binder in reactive mixtures does not exceed 50 vol.%. Porous SHS cakes were crashed and resulting granules were separated to fractions by screening to get the composite powder fraction necessary for coating application. Synthesis products were studied by optical and scanning electron microscopy, X-ray diffraction and electron microprobe analysis. It has been found that the average size of carbide inclusions depends on the content of thermally inert alloy powder in the reaction mixtures and can be purposefully regulated in a wide range. The microhardness of composite powder granules obtained by crushing the SHS conglomerates decreases monotonically with an increasing content of the metal binder having hardness less than that of titanium carbide. According to X-ray diffraction data, the titanium carbide lattice parameter turns out to be considerably less than values known for equiatomic titanium carbide. It has been found by electron microprobe analysis of carbide inclusions in the composite structure that the ratio of carbon and titanium mass contents is 0,21 as compared with 0,25 in equiatomic titanium carbide. Iron and silicon contents in the carbide are negligible, oxygen and nickel contents are below 1 wt.%, and chromium content is 2,5 wt.%. The analysis of known data on the effect of all the above-listed dopants on the titanium carbide lattice allows for a conclusion that the carbon deficit is a main reason of the lattice parameter reduction.

EFFECT OF COMPOSITION AND MECHANICAL PREPARATION METHOD OF A COMPOSITE TiC–Ni MIXTURE ON TITANIUM CARBIDE CONTENT IN COATINGS FORMED BY COLD SPRAYING

The Effect of Powder Preparation Method on the Corrosion and Mechanical Properties of TiN-based Coatings by Reactive Plasma Spraying

Effect of self-propagating high-temperature combustion synthesis on the deposition of NiTi coating by cold spraying using mechanical alloying Ni/Ti powder

Investigation of Preparation and Properties of TiCN Coatings by Reactive Plasma Spraying

Preparation and Properties of Composite Nanoceramic NiCrBSi-TiO2/WC(Co) Coatings

SYNTHESIS OF COMPOSITE POWDERS «TIC – NICRBSI ALLOY BINDER» FOR CLADDING AND DEPOSITION OF WEAR-RESISTANT COATINGS

Characterizations of Cold Sprayed Tin Particle Reinforced Al2319 Composite Coating

Investigation on Particles Reinforced Titanium Matrix Composite Coating Fabricated by Cold Spraying

In-situ TiC-Ti5Si3-SiC composite coatings prepared by plasma spraying

TiC-TiSi2-Al2O3 composite coatings prepared by spray drying, heat treatment and plasma spraying

Preparation method of titanium-based composite coating enhanced with nanometer titanium carbide and used on titanium alloy surface

Effect of Ball Milling of Feedstock Powder on Microstructure and Properties of Tin Particle-Reinforced Al Alloy-Based Composites Fabricated by Cold Spraying

Metal Matrix Composite Coatings Manufactured by Thermal Spraying: Influence of the Powder Preparation on the Coating Properties

Effect of Particle Morphology and Size Distribution on Cold-Sprayed Pure Titanium Coatings

Effect of Feedstock Powder Morphology on Cold-Sprayed Titanium Dioxide Coatings

Preparation and tribological properties of novel cold–sprayed Ti–diamond composite coating

Titanium-silicon-carbon reaction spraying composite powder and preparation method thereof

The Influence of Composition and Process Parameters on the Microstructure of TiC-Fe Coatings Obtained by Reactive Flame Spray Process

Deposition of Ti(C, N)-TiB2 Composite Coating by Reactive LPPS

Experiment Study of the Feedstock Character Effect on Composite Coating Deposition by Cold Spray

Influences Of Agglomeration Powder Preparation On Deposition Of Cold-Sprayed Ti2alc Coating