Abstract:Additive Manufacturing (AM) processes are becoming more and more important for production of parts with increasing geometrical complexity and functionality. However, to draw on the full potential of AM technologies, alloys that exploit process inherent particularities such as extremely high cooling rates (ca. 10 6 K/s) have to be developed. One of most important AM-processes is Laser Powder Bed Fusion (LPBF), a batch-wise process. This complicates experimental alloy development and increases the use of powder resources since only one chemical composition can be tested within one test job and the process chamber has to be cleaned carefully in between. The process Extreme High-Speed Laser Material Deposition (EHLA) has been found to have similar cooling rates as LPBF, however it uses an in situ supply of powders which allows an easy switching between materials and has potential for rapid alloy development methods. Since the mechanical properties of materials primarily depend on chemical composition and microstructure, which in turn depends heavily on the cooling rates in the production process, the EHLA-process could be used as a means for an accelerated alloy development for LPBF. However, to explore this possibility, a thorough comparison of the two processes has to be performed.In this work, EHLA and LPBF processes are compared and evaluated regarding the following characteristics: process parameters, laser intensities and volume energy densities, resulting microstructure (primary dendrite arm spacing, DAS), melt pool size and shape. The reference samples were manufactured using one set of LPBF process parameters and EHLA samples were manufactured using three different sets of process parameters.The volume energy densities E v [J/mm3] of the processes were found to differ by a factor 2.4 with higher E v observed in LPBF. However, considering that approximately 2 to 3 layers are remelted with each pass of the laser beam, the introduced E v per pass approximates the E v introduced in the EHLA process. The melt pool size as seen in a cross section in the EHLA-manufactured samples is approximately 25 times larger than in the LPBF-manufactured samples and its depth to width ratio (d/w ratio) can be attributed to a heat conduction welding process while the d/w ratio observed in the LPBF-manufactured sample suggests a transition process between heat conduction welding and deep welding. The observed DAS is in the same order of magnitude for both processes ranging from 0.55 to 1.15 μm in EHLA-manufactured samples and 0.73 μm in the LPBF-manufactured reference sample. Since the resulting microstructures of samples manufactured with both processes show this common feature and EHLA process parameters can be adjusted to control the cooling rates, the transferability between EHLA- and LPBF-processes is supported in this first investigation. Research for a more efficient alloy development for LPBF using EHLA will be continued by e.g. examining chemical compositions and performing mechanical testing.

Coating of Aluminum with High Deposition Rates through Extreme High-Speed Laser Application

Investigation of the coating of hydrodynamic plain bearing contact surfaces by means of Extreme High-Speed Laser Material Deposition (EHLA)

Comparison of the EHLA and LPBF Process in Context of New Alloy Design Methods for LPBF

Microstructure and Microhardness of High-Strength Aluminium Alloy Prepared Using High-Speed Laser Fabrication

A review on coatings deposited by extreme high-speed laser cladding: processes, materials, and properties

High-velocity laser accelerated deposition: Microstructure and mechanical properties of the aluminum-steel bonding interface

Laser Directed Energy Deposition of an AlMgScZr-Alloy in High-Speed Process Regimes

Research on the laser melting coating process of an AlCoCrFeNi high‐entropy alloy

Research status and prospect of extreme high-speed laser cladding technology

Laser Assisted Electrodeposition of Metals and Alloys

Laser-based Surface Modifications of Aluminum and its Alloys

Low-Defect AM of High Strength Aluminium Alloy by LMD

Parameter optimization of T800 coating fabricated by EHLA based on response surface methodology

Wear and Corrosion Resistant Eutectic High-Entropy Alloy Al0.3CoCrFeNiMo0.75 Produced by Laser Metal Deposition and Spark-Plasma Sintering

Research of On-Line Monitoring Technology Based on Laser Triangulation for Surface Morphology of Extreme High-Speed Laser Cladding Coating

Laser beam brazing of aluminum alloys in XHV-adequate atmosphere with surface deoxidation by ns-pulsed laser radiation

Investigation of GH3625 alloy: Contrasting microstructures, mechanical properties, and corrosion performance via conventional and extreme high speed laser material deposition

Atomic layer deposition of Al2O3 and HfO2 for high power laser application

Development of a laser preheating concept for directed energy deposition

Processability of high-strength aluminum 6182 series alloy via laser powder bed fusion (LPBF)

Microstructure Evolution and Wear Resistance of the Eutectic High-Entropy Alloy Al0.3CoCrFeNiNb0.5 Produced by Laser Metal Deposition