Abstract:Additive Manufacturing (AM) processes are becoming more and more important for production of parts with increasing geometrical complexity and functionality. However, to draw on the full potential of AM technologies, alloys that exploit process inherent particularities such as extremely high cooling rates (ca. 10 6 K/s) have to be developed. One of most important AM-processes is Laser Powder Bed Fusion (LPBF), a batch-wise process. This complicates experimental alloy development and increases the use of powder resources since only one chemical composition can be tested within one test job and the process chamber has to be cleaned carefully in between. The process Extreme High-Speed Laser Material Deposition (EHLA) has been found to have similar cooling rates as LPBF, however it uses an in situ supply of powders which allows an easy switching between materials and has potential for rapid alloy development methods. Since the mechanical properties of materials primarily depend on chemical composition and microstructure, which in turn depends heavily on the cooling rates in the production process, the EHLA-process could be used as a means for an accelerated alloy development for LPBF. However, to explore this possibility, a thorough comparison of the two processes has to be performed.In this work, EHLA and LPBF processes are compared and evaluated regarding the following characteristics: process parameters, laser intensities and volume energy densities, resulting microstructure (primary dendrite arm spacing, DAS), melt pool size and shape. The reference samples were manufactured using one set of LPBF process parameters and EHLA samples were manufactured using three different sets of process parameters.The volume energy densities E v [J/mm3] of the processes were found to differ by a factor 2.4 with higher E v observed in LPBF. However, considering that approximately 2 to 3 layers are remelted with each pass of the laser beam, the introduced E v per pass approximates the E v introduced in the EHLA process. The melt pool size as seen in a cross section in the EHLA-manufactured samples is approximately 25 times larger than in the LPBF-manufactured samples and its depth to width ratio (d/w ratio) can be attributed to a heat conduction welding process while the d/w ratio observed in the LPBF-manufactured sample suggests a transition process between heat conduction welding and deep welding. The observed DAS is in the same order of magnitude for both processes ranging from 0.55 to 1.15 μm in EHLA-manufactured samples and 0.73 μm in the LPBF-manufactured reference sample. Since the resulting microstructures of samples manufactured with both processes show this common feature and EHLA process parameters can be adjusted to control the cooling rates, the transferability between EHLA- and LPBF-processes is supported in this first investigation. Research for a more efficient alloy development for LPBF using EHLA will be continued by e.g. examining chemical compositions and performing mechanical testing.

Processability of high-strength aluminum 6182 series alloy via laser powder bed fusion (LPBF)

Effect of Powder Spreading Parameters on Laser Absorption Behavior and Processability of High‐Strength Aluminum Alloy Fabricated by Laser Powder Bed Fusion

Effect of laser process parameters on thermal behavior and residual stress of high-strength aluminum alloy processed by laser powder bed fusion

Effect of Aluminium Content and Processing Parameters on the Microstructure and Mechanical Properties of Laser Powder-Bed Fused Magnesium-Aluminium (0, 3, 6, 9wt%) Powder Mixture

Processability of A6061 Aluminum Alloy Using Laser Powder Bed Fusion by In Situ Synthesis of Grain Refiners

Systematic approach to process parameter optimization for laser powder bed fusion of low-alloy steel based on melting modes

Microstructure, mechanical properties, and crack formation of aluminum alloy 6063 produced via laser powder bed fusion

The influence of beam focus during laser powder bed fusion of a high reflectivity aluminium alloy -- AlSi$_{10}$Mg

Formability and microstructure of laser powder bed fused AlSi10Mg alloy sheets under various deformation conditions

Circumventing Solidification Cracking Susceptibility in Al–Cu Alloys Prepared by Laser Powder Bed Fusion

Spreading Behavior and Hot Cracking Mechanism of Single Tracks in High Strength Al–Cu–Mg–Mn Alloy Fabricated by Laser Powder Bed Fusion

Joining of Aluminum and CFRP via Laser Powder Bed Fusion: Influence of Experimental Set-Up and Laser Processing on Microstructure and Mechanical Properties

Fabrication of crack-free aluminum alloy 6061 parts using laser foil printing process

Cracking mechanism and its susceptibility to scanning speed during laser power bed fusion processed high-strength 2024Al alloy

Comparison of the EHLA and LPBF Process in Context of New Alloy Design Methods for LPBF

A357 Alloy by LPBF for Industry Applications

Processing defect, microstructure evolution and mechanical properties of laser powder bed fusion Al-12Si alloys

Advancements in metal additive manufacturing: In-situ heat treatment of aluminium alloys during the laser powder bed fusion process

Recent progress on the control strategies of microstructure and mechanical properties of LPBF-printed aluminum alloys

Processability and Optimization of Laser Parameters for Densification of Hypereutectic Al–Fe Binary Alloy Manufactured by Laser Powder Bed Fusion

Unveiling the impact of layerwise laser preheating on microstructure and mechanical response in laser powder bed fusion