Abstract:High entropy alloys (HEAs) are promising materials with equiatomic or near-equiatomic multicomponent structures in the field of corrosion and abrasion resistance. In order to prolong the service life of corrosion and abrasion resistance for drilling pipes in offshore petroleum exploration, CoCr(2.5)FeNi(2)Tix (x = 0, 0.5, 1, 1.5) high-entropy alloy (HEA) coatings were successfully fabricated by a laser-cladding technique. The phase structures, microstructure, hardness, wear and corrosion resistance of HEA coatings were specifically investigated. The experimental results indicate that the CoCr(2.5)FeNi(2)Tix HEA exhibits an excellent bonding ability between the cladding layer and the substrate. The cladding zone is composed mainly of equiaxed grains and columnar crystal; the phase structures of the CoCr(2.5)FeNi(2)Tix coatings are composed of BCC (Ti = O) and solid composition of BCC + FCC phases with the addition of Ti due to the high-entropy effect. Ti element promotes the formation of an FCC structure. During the solidification process of the HEA alloy, some Ti atoms were excluded from the solid solution. Based on Gibbs free energy, the repulsion of Ti atoms was analyzed under the condition of the equilibrium state. With the increasing Ti content, the corrosion resistance of CoCr(2.5)FeNi(2)Tix high-entropy alloy coatings are found enhanced in a simulated saturated salty water mud solution. The relative wear resistance of CoCr(2.5)FeNi(2)Tix high-entropy alloy coatings was found significantly improved almost 2 times than the Q235 steel. The highest average micro-hardness value (Ti = 1.5) of HEA coatings is 480 HV0.2, which is more than 2.4 times higher than that of the substrate. The HEA coating CoCr2.5FeNi2Ti exhibited the prominent corrosion resistance and excellent wear resistance indicated by lower volume wear rates and smoother worn surface under the same conditions among the four coatings. (C) 2019 Elsevier B.V. All rights reserved.

Wear and Corrosion Resistant Eutectic High-Entropy Alloy Al0.3CoCrFeNiMo0.75 Produced by Laser Metal Deposition and Spark-Plasma Sintering

Microstructure Evolution and Wear Resistance of the Eutectic High-Entropy Alloy Al0.3CoCrFeNiNb0.5 Produced by Laser Metal Deposition

Supersaturated Solid Solution Formation in the Metastable Eutectic High-Entropy Alloy Al0.3CoCrFeNiMo0.75 by Laser Metal Deposition and Degradation of Wear Resistance by Segregation

Microstructure and Properties of AlCoCrFeNi2.1 Eutectic High-Entropy Alloy Coatings Fabricated by Extreme High-Speed and Conventional Laser Cladding

Mechanical properties of nanostructured CoCrFeNiMn high-entropy alloy (HEA) coating

Preparation of CrCoFeNiMn High-Entropy Alloy Coatings Using Gas Atomization and Laser Cladding: An Investigation of Microstructure, Mechanical Properties, and Wear Resistance

Microstructure and wear behavior of mechanically alloyed powder AlxMo0.5NbFeTiMn2 high entropy alloy coating formed by laser cladding

CoCrFeNiMo0.2 High Entropy Alloy by Laser Melting Deposition: Prospective Material for Low Temperature and Corrosion Resistant Applications

Microstructure and Properties of Laser Cladding and CoCr2.5FeNi2Tix High-Entropy Alloy Composite Coatings

Surface modification for AlCoCrFeNi2.1 eutectic high-entropy alloy via laser remelting technology and subsequent aging heat treatment

Microstructural evolution and properties of dual-layer CoCrFeMnTi0.2 high-entropy alloy coating fabricated by laser cladding

Microstructure and high-temperature wear behavior of CoCrFeNiWx high-entropy alloy coatings fabricated by laser cladding

Effect of Nanostructure on Wear and Corrosion Behavior of HVAF-Sprayed Eutectic High-Entropy Alloy Coatings

Laser metal deposition of thin-walled parts of Al 0.8 CrFe 2 Ni 2 high-entropy alloy: Process window, microstructure, wear resistance and mechanical anisotropy

Design and Characterization on Microstructure Evolution and Properties of Laser-Cladding Ni1.5CrFeTi2B0.5Mox High-Entropy Alloy Coatings

Corrosion and slurry erosion wear performances of coaxial direct laser deposited CoCrFeNiCu1-xMox high-entropy coatings by modulating the second-phase precipitation

Microstructure and Wear Properties of Mechanically Alloyed Powder Al x Mo 0.5 NBFeTiMn 2 High Entropy Alloy Coating by Laser Cladding

Study on Mechanical Properties of AlFeCrMoNi1.8Nb1.5 Eutectic High-Entropy Alloy Coating Prepared by Wide-Band Laser Cladding

Non-Metallic Alloying Constituents to Develop a Wear-Resistant CrFeNi-BSiC High-Entropy Alloy for Surface Protective Coatings by Thermal Spraying and High-Speed Laser Metal Deposition

Mechanical, materials, and physicochemical effects on the high-temperature tribological behaviour of laser additive manufacturing AlCoCrFeNi2.1 eutectic high-entropy alloys

FeNiCrCoCuxMo High Entropy Alloy (HEA) Coatings Fabricated by Laser Cladding