Abstract:Aluminum alloy plates show great potential in energy storage and transportation applications. Nevertheless, the low surface strength of aluminum alloy plates negatively impacts their performance and safety. Aluminum alloys exhibit characteristics such as a low melting point, high reflectivity, and a rapid dilution rate, posing significant challenges for laser cladding coatings. This paper presented the surface modification mechanism of aluminum alloy plates. A stainless steel coating was successfully prepared on the surface of aluminum alloy substrates by using high-speed laser cladding technology. The microstructure, microscopic morphology, and microhardness of the coatings were conducted. The surface and sides of coatings were analyzed by XRD, SEM, EBSD, and microhardness testing, respectively. It is found that larger cellular crystals and carbides predominate at the junction of the substrate and the coating. The middle part of the 0.5-mm coating from the connection and the heat-affected zone are mainly dendritic crystals. The top of the 1-mm coating from the connection is mainly fine crystals. This means that local grain refinement occurs in the stainless steel coating via high-speed laser cladding. There is a transformation of FCC to BCC in the coating. Moreover, the cross-section of the coating exhibits a relatively high microhardness, ranging from 517 to 679 HV. The microhardness at the substrate is measured at 67 HV. The maximum microhardness of the coating is ten times that of the substrate. The bottom of the coating maintains a relatively high microhardness due to the presence of a large amount of carbides. The microhardness of the coating gradually increases from the middle to the surface of the coating. This is primarily attributed to solid solution strengthening and fine grain strengthening mechanisms. Columnar crystals at the metallurgical bond between the substrate and the coating transform into fine grains at the top, leading to a gradual refinement of the microstructure. High-speed laser cladding technology facilitates the enhancement of surface properties and the improvement of surface strength in traditional aluminum alloys.

High-velocity laser accelerated deposition: Microstructure and mechanical properties of the aluminum-steel bonding interface

Microstructure and Mechanical Properties of Ti-6al-4v Components Fabricated by Laser Micro Cladding Deposition

Microstructure and strengthening mechanism of a 316 stainless steel coating prepared by high-speed laser cladding on an aluminum alloy plate

Microstructure and Microhardness of High-Strength Aluminium Alloy Prepared Using High-Speed Laser Fabrication

Microstructure and Properties of Metallic Coatings with Low Dilution Ratio by High Speed Laser Cladding

Experiment on Injection Powder Laser Cladding Forming L-Alloy

A high strength low alloy steel fabricated by direct laser deposition

Integrated laser additive manufacturing of high-strength steel and Ti6Al4V: Experimental investigations and thermodynamic calculations

Laser Directed Energy Deposition of an AlMgScZr-Alloy in High-Speed Process Regimes

Data related to optimized process parameters influence on hardness, microstructural evolution and wear resistance performance of Al-Si-Sn-Cu/Ti-6Al-4V composite coatings

Coating of Aluminum with High Deposition Rates through Extreme High-Speed Laser Application

Deposition of Nickel-Based Superalloy Claddings on Low Alloy Structural Steel by Direct Laser Deposition

The study of hot deformation on laser cladding remanufactured 316L stainless steel

Investigation of GH3625 alloy: Contrasting microstructures, mechanical properties, and corrosion performance via conventional and extreme high speed laser material deposition

The Interplay of Thermal Gradient and Laser Process Parameters on the Mechanical Properties, Geometrical and Microstructural Characteristics of Laser-Cladded Titanium (Ti6Al4V) Alloy Composite Coatings

An Investigation of the Surface Quality and Corrosion Resistance of Laser Remelted and Extreme High-Speed Laser Cladded Ni-based Alloy Coating

An Overview of Laser Metal Deposition for Cladding: Defect Formation Mechanisms, Defect Suppression Methods and Performance Improvements of Laser-Cladded Layers

Improvement of thermal plasma sprayed coating adhesion strength by laser microtexturing of aluminum

Research on the laser melting coating process of an AlCoCrFeNi high‐entropy alloy

Process, microstructure and microhardness of GH3039 superalloy processed by laser metal wire deposition

Laser Metal Deposition of Ti6Al4V—A Brief Review