Abstract:Laser-based metal additive manufacturing technology, which is represented by laser powder bed fusion (LPBF) and direct energy deposition (DED), has been widely used in high-end industries such as aerospace. However, with the rapid development of aerospace equipment, it has become increasingly difficult to meet the requirements of integrated design and manufacturing of metal parts by using LPBF or DED alone. LPBF/DED hybrid laser additive manufacturing technology is expected to greatly improve the overall manufacturing capacity of metal components by combining the advantages of the two technologies. It is expected to break through the limitation of overall manufacturing size, to realize the manufacturing of large and complex aerospace parts, and to reduce the number of components required for large and complex structures to meet the overall design and manufacturing requirements. In this paper, AlSi10Mg was selected as the build material for the LPBF/DED hybrid laser additive manufacturing process and the microstructure and mechanical properties of the as-built samples were studied. The analyses of the microstructure show that there are no obvious defects at the interface between the LPBF zone and the DED zone. Although the phase compositions of both the LPBF zone and the DED zone are composed of alpha-Al matrix and eutectic Si, the melt track shape, microstructural morphology, grain size, grain boundary angle distribution and grain texture change significantly around the LPBF/DED interface. The results of mechanical property tests indicated that the LPBF zone has higher microhardness and tensile strength but lower elongation in comparison with the DED zone. The fine microstructure containing a large number of Si-rich nano-precipitates and high amount of solid solution element enhance the microhardness and tensile strength of the LPBF zone, where the lower solid solubility and high percentage of low angle grain boundary increased the elongation of the DED zone. More importantly, the tensile strength of the LPBF/DED interface is not less than the DED zone, and the boundary of DED melt track as well as porosity defect in the DED zone are the weakest region of LPBF/DED hybrid laser additive manufacturing AlSi10Mg specimens. Therefore, the overall tensile strength of the sample is mainly determined by the DED zone. The formation mechanism of the gradient microstructure around the LPBF/DED interface and the effect of microstructure on properties were also analyzed. This paper proves that the LPBF/DED hybrid laser additive manufacturing technology can be used for the overall manufacturing of aluminum alloy components with regular surface structure.

A high strength low alloy steel fabricated by direct laser deposition

Microstructure and Mechanical Properties of an Ultra-High Strength Steel Fabricated by Laser Hybrid Additive Manufacturing

Microstructure and Mechanical Properties of High-Strength, Low-Alloy Steel Thin-Wall Fabricated with Wire and Arc Additive Manufacturing

A Comparative Study of Microstructural Characteristics and Mechanical Properties of High-Strength Low-Alloy Steel Fabricated by Wire-Fed Laser Versus Wire Arc Additive Manufacturing

Dt300 Ultra-High Strength Steel Fabricated Using Selective Laser Melting: Densification, Microstructure, and Mechanical Properties

High-strength Lamellar High-Entropy Alloys In-Situ Synthesized by Laser Additive Manufacturing

Strain hardening and strengthening mechanism of laser melting deposition (LMD) additively manufactured FeCoCrNiAl0.5 high-entropy alloy

Tailoring Microstructure Evolution and Mechanical Properties of a High-Performance Alloy Steel Through Controlled Thermal Cycles of a Direct Laser Depositing Process

In-situ alloyed ultrahigh strength steels via additive manufacturing

Comparison on Microstructure and Properties of Stainless Steel Layer Formed by Extreme High-Speed and Conventional Laser Melting Deposition

Superior strength-ductility in laser aided additive manufactured high-strength steel by combination of intrinsic tempering and heat treatment

Functionally Graded Stainless Steel Fabricated by Direct Laser Deposition: Anisotropy of Mechanical Properties and Hardness

Titanium Alloy Components Fabrication by Laser Depositing TA15 Powders on TC17 Forged Plate: Microstructure and Mechanical Properties

High-velocity laser accelerated deposition: Microstructure and mechanical properties of the aluminum-steel bonding interface

Unique Strength-Ductility Balance of AlCoCrFeNi2.1 Eutectic High Entropy Alloy with Ultra-Fine Duplex Microstructure Prepared by Selective Laser Melting

Selective Laser Melting of High Strength Al–Cu–Mg Alloys: Processing, Microstructure and Mechanical Properties

Microstructure and Tensile Properties of High-Deposition-Rate Laser Metal Deposited GH4169 Alloy

Microstructure and mechanical properties of AlSi10Mg alloy built by laser powder bed fusion/direct energy deposition hybrid laser additive manufacturing

Microstructure and Mechanical Properties of Fe-30Mn-9Al-C-3Ni Low-Density Steel Manufactured by Selective Laser Melting

Achieving High Strength 316L Stainless Steel by Laser Directed Energy Deposition-Ultrasonic Rolling Hybrid Process

An ultra-high strength martensitic steel fabricated using selective laser melting additive manufacturing: Densification, microstructure, and mechanical properties