Abstract:Experimental results obtained on the preparation of hydrophobic silica aerogels by ambient pressure drying method using the sodium silicate precursor with the variation of solvent exchanging process, are reported. The silica hydrogel was prepared by passing the 1.12 specific gravity sodium silicate through the Amberlite (TM) 120 Na+ resin and addition of 1 M ammonium hydroxide to silicic acid. The gel was kept in an oven for 3 h to strengthen the gel. Solvent exchange was carried out with ethanol and hexane for 36 h each followed by 24 h silylation using 20% hexamethyldisilazane (HMDZ) in hexane. Unreacted HMDZ was washed with hexane by keeping the gel in hexane for 24 h. Solvent was decanted and the gel was dried for 24 h by keeping the gel at 50 °C for 6 h, at 150 °C for 12 h and at 200 °C for 6 h. The low density (0.06 g/cm3), highly porous (96.9%), highly hydrophobic (contact angle of 160°), low thermal conductivity (0.07 W/m K) aerogels were obtained for the process of three times exchange with ethanol and three times exchange with hexane in 36 h each, followed by silylation with 20% HMDZ in hexane and two times washing with hexane in 24 h. FTIR studies showed the increase in the intensity of the Si–H and C–H bands of the aerogels with the increase of solvent exchanging times because of increase in silylation for more times of solvent exchange processes. It was found from the TG–DTA studies that the hydrophobicity of the aerogels retained up to the temperature of 325 °C. Water absorption studies show that the aerogels were remained hydrophobic up to 4 months when the aerogels were placed over the water as well as for up to 60 h in a 90% humid atmosphere. SEMs of the aerogels reveal that the pore sizes of the silica network increased, so the percentage of optical transparency decreased with the increase in exchange times with ethanol and hexane.

Modulating pore microstructure of silica aerogels dried at ambient pressure by adding N-hexane to the solvent

Regulating the hydrophobicity and pore structure of silica aerogel for thermal insulation under humid and high temperature conditions

Synthesis and Effect of DCCA on the Ambient Pressure Dried, TEOS-Based Silica Aerogel

Preparation of Methyltrimethoxysilane Derived Silica Aerogel Films via Ambient Pressure Drying

Enhancing Mesopore Volume and Thermal Insulation of Silica Aerogel via Ambient Pressure Drying-Assisted Foaming Method

Effect of Modifier on the Characteristics of Silica Aerogels

Rapid Synthesis of Super Insulation Silica Aerogel Composites Strengthened with Mullite Fibers

Thermal Conductivity of Silica Aerogel Thermal Insulation Coatings

Effect of solvent exchanging process on the preparation of the hydrophobic silica aerogels by ambient pressure drying method using sodium silicate precursor

Synthesis of high specific surface area silica aerogel from rice husk ash via ambient pressure drying

Facile Synthesis of Flexible and Hydrophobic Polymethylsilsesquioxane Based Silica Aerogel Via the Co-Precursor Method and Ambient Pressure Drying Technique

Synthesis and Characterization of Silica Aerogel and Its Composite Materials

Performance regulation of silica aerogel powder synthesized by a two-step Sol-gel process with a fast ambient pressure drying route

Preparation of silica aerogel in surfactant-free microemulsion system

Synthesis and Characterization of Silica Aerogel Materials Doped with TiO2 Powder for Thermal Insulation

Synthesis and Characterization of Silica Aerogels Dried under Ambient Pressure Bed on Water Glass

Hydrosilylation Adducts to Produce Wide‐Temperature Flexible Polysiloxane Aerogel under Ambient Temperature and Pressure Drying

Synthesis and characterization of silica aerogels by a novel fast ambient pressure drying process

Effects of Surfactants on the Synthesis of Silica Aerogels Prepared by Ambient Pressure Drying

Improvement of the Thermal Insulation Performance of Silica Aerogel by Proper Heat Treatment: Microporous Structures Changes and Pyrolysis Mechanism

Effects of several additives on silica aerogel properties and adsorption performance for n-hexane, carbon tetrachloride and toluene