Abstract:In machining, heat concentration is generated at the surface contact between the tool and workpiece. This is the effect of hard frictions at the shear cutting plane to remove hard and brittle materials. The highly adhesive behavior of aluminum alloy 6061-T6 is more severe in higher cutting temperature, which may affect tool failures such as flank wear, tool chip and built-up edge, particularly on the edge of cutting inserts during the process. As a result, this may lead to the rough surface and low-dimensional accuracy of the machined parts. Realizing that metal-cutting industry players are demanding high-quality products with better surface finish and dimensional accuracy led to this study. Aluminum alloy 6061-T6 is a standard alloy used in automotive, aerospace and food packaging due to good hardness, high strength-to-weight ratio, resistance to corrosion and weldability. In order to address this problem, a newly developed metal working fluid which is SiO2-Al2O3-ZrO2 tri-hybrid nanofluid is applied in the cutting zone to achieve a good surface finish of the machined parts and lowering the cutting temperature. This study is the first attempt to enhance machining performance, particularly at high-speed machining, by employing a combination of tri-hybrid nanofluids and a minimum quantity lubricant technique. Industrial standards include uncoated tungsten carbide and CVD TiCN-Al2O3 carbide used during machining of aluminum alloy 6061-T6. The minimum quantity lubricant method is an alternative in supplying the lubricant into the machining zone due to flood machining and conventional fluid possess safety, health, economic and environmental effects. In this study, the experimental data were analyzed statistically using analysis of variance and response surface methodology. The responses studied were reduced significantly when tri-hybrid nanoparticles present at the cutting interface with higher MQL flow rate and concentration. There are two-factor interactions which are significant to the responses studied. Therefore, the combinations of MQL and excellent tri-hybrid nanofluids characteristics have enhanced between 16 and 76% of surface roughness and the cutting temperature, respectively, which is very promising in the future.

Adjusting machined surface integrity of aluminum–silicon alloy through step-by-step feed cutting and multi-step finish cutting method

Surface integrity enhancement of ZL109 aluminum-silicon piston alloy employing the forward and reverse finish cutting method

Effect of machined surface integrity on fatigue resistance of aluminum-silicon alloy ZL109

Multi-step Cutting Depth Optimization Method Based on the Removal Mechanism of SiCp/Al

Experimental Investigation on Machinability of Aluminum Alloy during Dry Micro Cutting Process Using Helical Micro End Mills with Micro Textures

Research on surface integrity and its influencing factors in the high-speed cutting of typical aluminum/titanium/nickel alloys: a review

Prediction of surface roughness and optimization of process parameters for efficient cutting of aluminum alloy

Effect of Surface Micro-Hardness Change in Multistep Machining on Friction and Wear Characteristics of Titanium Alloy

Towards the understanding the effect of surface integrity on the fatigue performance of silicon carbide particle reinforced aluminium matrix composites

CHARACTERIZATION OF SURFACE, SUBSURFACE DAMAGE AND THEIR EFFECT ON FATIGUE LIFE AFTER MACHINING OF AEROSPACE-GRADE ALUMINUM ALLOY (Al 6082-T6)

Review of improvement of machinability and surface integrity in machining on aluminum alloys

Finite element and experimental analysis of surface integrity and surface roughness of precision machining SiCp/Al

Effect of surface roughness on stress concentration factor of machined surface and cutting parameter optimization in boring of Al-Si piston alloy

Investigation of Surface Integrity of Selective Laser Melting Additively Manufactured AlSi10Mg Alloy under Ultrasonic Elliptical Vibration-Assisted Ultra-Precision Cutting

Study on micro-grinding mechanism and surface quality of hardened 20 vol% SiCp/Al composites

Surface defects formation mechanism of Mg 2 Si/Al composites by micro cutting

Effects of SiO2-Al2O3-ZrO2 Tri-hybrid Nanofluids on Surface Roughness and Cutting Temperature in End Milling Process of Aluminum Alloy 6061-T6 Using Uncoated and Coated Cutting Inserts with Minimal Quantity Lubricant Method

Improving fatigue properties of normal direction ultrasonic vibration assisted face grinding Inconel 718 by regulating machined surface integrity

Cutting path-dependent machinability of SiCp/Al composite under multi-step ultra-precision diamond cutting

Cutting condition effects on microstructure and mechanical characteristics of Ni-based superalloys—a review

Study on formation mechanism of edge defects of high-volume fraction SiCp/Al composites by longitudinal-torsional ultrasonic vibration-assisted milling