Abstract:In machining, heat concentration is generated at the surface contact between the tool and workpiece. This is the effect of hard frictions at the shear cutting plane to remove hard and brittle materials. The highly adhesive behavior of aluminum alloy 6061-T6 is more severe in higher cutting temperature, which may affect tool failures such as flank wear, tool chip and built-up edge, particularly on the edge of cutting inserts during the process. As a result, this may lead to the rough surface and low-dimensional accuracy of the machined parts. Realizing that metal-cutting industry players are demanding high-quality products with better surface finish and dimensional accuracy led to this study. Aluminum alloy 6061-T6 is a standard alloy used in automotive, aerospace and food packaging due to good hardness, high strength-to-weight ratio, resistance to corrosion and weldability. In order to address this problem, a newly developed metal working fluid which is SiO2-Al2O3-ZrO2 tri-hybrid nanofluid is applied in the cutting zone to achieve a good surface finish of the machined parts and lowering the cutting temperature. This study is the first attempt to enhance machining performance, particularly at high-speed machining, by employing a combination of tri-hybrid nanofluids and a minimum quantity lubricant technique. Industrial standards include uncoated tungsten carbide and CVD TiCN-Al2O3 carbide used during machining of aluminum alloy 6061-T6. The minimum quantity lubricant method is an alternative in supplying the lubricant into the machining zone due to flood machining and conventional fluid possess safety, health, economic and environmental effects. In this study, the experimental data were analyzed statistically using analysis of variance and response surface methodology. The responses studied were reduced significantly when tri-hybrid nanoparticles present at the cutting interface with higher MQL flow rate and concentration. There are two-factor interactions which are significant to the responses studied. Therefore, the combinations of MQL and excellent tri-hybrid nanofluids characteristics have enhanced between 16 and 76% of surface roughness and the cutting temperature, respectively, which is very promising in the future.

Effect of surface roughness on stress concentration factor of machined surface and cutting parameter optimization in boring of Al-Si piston alloy

A Multiscale Evaluation of the Surface Integrity in Boring Trepanning Association Deep Hole Drilling

Surface integrity enhancement of ZL109 aluminum-silicon piston alloy employing the forward and reverse finish cutting method

Modeling and optimization of surface residual stress profiles in milling of aluminum 7075-T6 alloy

Precision machining of an aluminum alloy piston reinforced with a cast iron insert

An optimization investigation on surface roughness and its evolution with tool wear in dry turning of boron alloy cast iron

Optimization of Surface Quality and Power Consumption in Machining Hardened AISI 4340 Steel

3D Coupled Thermo-Mechanical Simulation of Surface Roughness and Residual Stress in End Milling Aluminum Alloy

The optimization of cutting parameters for surface roughness in high speed milling based on Taguchi method

Modeling and Optimization of Tool Wear and Surface Roughness in Turning of Al/SiCp Using Response Surface Methodology

Development of surface textures using micro-milling operation for improved tribological characteristics of aluminium alloy

Fuzzy logic based model for predicting surface roughness of machined Al–Si–Cu–Fe die casting alloy using different additives-turning

Machining-induced residual stress analysis and multi-objective optimization for milling process of Mg–Li alloy

Finite element and experimental analysis of surface integrity and surface roughness of precision machining SiCp/Al

Prediction of surface roughness and optimization of process parameters for efficient cutting of aluminum alloy

3D surface topography analysis and functionality-related performance of the machined surface in slot micro-milling titanium alloy Ti6Al4V

Simulation and experimental investigation on low wear rate surface contour of piston/cylinder pair in an axial piston pump

Experimental Study for Optimizing Superfinishing Process Parameters of High-Quality Alloy Bearing Steel

Adjusting machined surface integrity of aluminum–silicon alloy through step-by-step feed cutting and multi-step finish cutting method

Effects of SiO2-Al2O3-ZrO2 Tri-hybrid Nanofluids on Surface Roughness and Cutting Temperature in End Milling Process of Aluminum Alloy 6061-T6 Using Uncoated and Coated Cutting Inserts with Minimal Quantity Lubricant Method

Effect of machined surface integrity on fatigue resistance of aluminum-silicon alloy ZL109