Abstract:Superior properties of titanium alloy Ti-6Al-4V over many other materials like higher strength to weight ratio, ability to maintain strength at elevated temperatures (around 500 degrees C) and ability to resist against corrosion in severe environmental conditions have made them as an excellent choice for using them in many aerospace and biomedical industrial applications. But the properties which had made them an ideal choice for most practical applications severely hinders their machinability and therefore is renowned as difficult to machine material. The low thermal conductivity of titanium alloys does not allow the generated heat to dissipate away quickly and thus results in chemical reaction with cutting tool materials at higher temperatures. Several researchers have tried to reduce tool-chip interface temperature, increase tool life and surface quality with carbide tools by applying different cutting fluids like water based emulsions flood cooling, oil flood coolant, minimum quantity lubrication MQL and various liquid nitrogen LiN cryogenic cooling techniques and has found some advantages of MQL & LiN cooling in terms of not only in improved surface roughness & tool life but also in controlling the hazardous environmental impact by eliminating the use of hazardous and expensive traditional flood coolant equipment. Moreover the thrust for higher quality and productivity has directed the attention of researchers on using super hard cutting tool materials for machining of titanium alloys. Super hard cutting tool like polycrystalline diamond PCD, Poly Cubic Boron Nitride PCBN and Binderless CBN inspite of their higher cost has many advantages over carbide tools like higher thermal conductivity, lower wear rate and high hot strength. Studies have shown that PCD tools can give better tool life and surface roughness as compared to carbide and PCBN tools. The studies on evaluating the effectiveness of PCD insert in high speed end milling of titanium alloy has not yet considered the effect of different types of cooling strategies. Therefore there is need to study the effectiveness of PCD tools in various wet cutting conditions and find optimal coolant which can help to increase tool life and can provide better surface quality and therefore this study is specifically designed to address above mentioned issues. Four different type of coolants "water based flood cooling, oil based flood coolant, MQL and LIN cryogenic cooling technique has been applied and their effect on tool-chip interface temperature, tool edge temperature, cutting forces and stresses acting on tool edge are observed using Finite element, FE numerical simulations. FE numerical simulations are widely employed in academic research field because it provides fast & reliable results and thus eliminates expensive experimentation costs which otherwise is always required. Results have shown that the LiN cooling technique has shown clear advantages over MQL and flood coolant techniques in terms of temperature near the tool rake face and in reducing cutting forces and stresses acting on cutting edge. Therefore from the study it can be concluded that LiN cooling can be used for machining of titanium alloys with PCD inserts for getting maximum productivity and part quality.

Application of a Cryogenic Cooling System on the Grinding Operation of Polyether Ether Ketone Biomaterial (PEEK)

Grinding performance study of CF/epoxy and CF/PEEK composites

Effect of Fiber Type and Content on Surface Quality and Removal Mechanism of Fiber-Reinforced Polyetheretherketone in Ultra-Precision Grinding

Investigation on grinding temperature characteristics of CF/PEEK and material removal mechanism under temperature treatments

Experimental Study on the Cooling Effects of Cryogenic Pneumatic Mist Jet Impinging Cooling Method

Research on Cryogenic Pneumatic Mist Jet Impinging Cooling and Lubricating of Grinding Processes

Innovative Technology Investigation into Cryogenic Cooling Green Grinding Using Liquid Nitrogen Jet

Evaluating the Effectiveness of PCD Tools on Machinability of Titanium Alloy Ti-6Al-4V in High Speed End Milling under Various Wet Cutting Conditions

Analytical and Experimental Investigation of the Nickel Based Superalloy Using Cryogenic Cooling Grinding

The Cooling Effects of Cryogenic Pneumatic Mist Jet Impinging in Grinding of Titanium Alloy

Effects of Cold Air Supply on Cutting Characteristics in Small Hole Drilling of PEEK

Effects of grinding mode on grinding performance of anisotropic CF/PEEK composites

Grinding performance investigation of multidirectional CF/PEEK composites—A comparative with unidirectional CF/PEEK

Study of milling process basics for the biocompatible PEEK material

A New Technology On Enhancing Heat Transfer During Grinding Of Titanium Alloy

Experimental study on the cytocompatibility of milling surface of poly-ether-ether-ketone (PEEK)

A State of the Art on Cryogenic Cooling and Its Applications in the Machining of Difficult-to-Machine Alloys

Influence of water-based copper nanofluid on wheel loading and surface roughness during grinding of Inconel 738 superalloy

Investigations on pulsed and continuous supply of a cryogenic medium in milling of Waspaloy and Inconel 718 under various lubri-cooling environments

Tool wear mechanisms and its influence on machining tribology of face milled titanium alloy under sustainable hybrid lubri-cooling