Abstract:Superior properties of titanium alloy Ti-6Al-4V over many other materials like higher strength to weight ratio, ability to maintain strength at elevated temperatures (around 500 degrees C) and ability to resist against corrosion in severe environmental conditions have made them as an excellent choice for using them in many aerospace and biomedical industrial applications. But the properties which had made them an ideal choice for most practical applications severely hinders their machinability and therefore is renowned as difficult to machine material. The low thermal conductivity of titanium alloys does not allow the generated heat to dissipate away quickly and thus results in chemical reaction with cutting tool materials at higher temperatures. Several researchers have tried to reduce tool-chip interface temperature, increase tool life and surface quality with carbide tools by applying different cutting fluids like water based emulsions flood cooling, oil flood coolant, minimum quantity lubrication MQL and various liquid nitrogen LiN cryogenic cooling techniques and has found some advantages of MQL & LiN cooling in terms of not only in improved surface roughness & tool life but also in controlling the hazardous environmental impact by eliminating the use of hazardous and expensive traditional flood coolant equipment. Moreover the thrust for higher quality and productivity has directed the attention of researchers on using super hard cutting tool materials for machining of titanium alloys. Super hard cutting tool like polycrystalline diamond PCD, Poly Cubic Boron Nitride PCBN and Binderless CBN inspite of their higher cost has many advantages over carbide tools like higher thermal conductivity, lower wear rate and high hot strength. Studies have shown that PCD tools can give better tool life and surface roughness as compared to carbide and PCBN tools. The studies on evaluating the effectiveness of PCD insert in high speed end milling of titanium alloy has not yet considered the effect of different types of cooling strategies. Therefore there is need to study the effectiveness of PCD tools in various wet cutting conditions and find optimal coolant which can help to increase tool life and can provide better surface quality and therefore this study is specifically designed to address above mentioned issues. Four different type of coolants "water based flood cooling, oil based flood coolant, MQL and LIN cryogenic cooling technique has been applied and their effect on tool-chip interface temperature, tool edge temperature, cutting forces and stresses acting on tool edge are observed using Finite element, FE numerical simulations. FE numerical simulations are widely employed in academic research field because it provides fast & reliable results and thus eliminates expensive experimentation costs which otherwise is always required. Results have shown that the LiN cooling technique has shown clear advantages over MQL and flood coolant techniques in terms of temperature near the tool rake face and in reducing cutting forces and stresses acting on cutting edge. Therefore from the study it can be concluded that LiN cooling can be used for machining of titanium alloys with PCD inserts for getting maximum productivity and part quality.

Effects of Cold Air Supply on Cutting Characteristics in Small Hole Drilling of PEEK

High-Precision Small-Diameter Deep Hole Drilling Using Cooling and Step Feed in PEEK Resin

Cutting force, Vibration, and Temperature in Drilling on a Thermoplastic Material of PEEK

Small Hole Drilling for Polyphenylene Sulfide (PPS) - Influence of Depth-of-Cut on Burr Formation

Effects of Drilling Parameters on Drilling of PEEK-CF30 Thermoplastic Material: Thrust Force, Surface Roughness and Delamination

Application of a Cryogenic Cooling System on the Grinding Operation of Polyether Ether Ketone Biomaterial (PEEK)

Cryogenic auxiliary drilling of printed circuit boards

Experimental Study of Micro-hole Pecking Drilling in High Volume Fraction SiCp/Al7075 Composites with Variable Step Size

Investigation of the effect of the cut parameter on the machining performance of PTFE cutting

On the Machining Behavior of Carbon Fiber Reinforced Polyimide and PEEK Thermoplastic Composites

A sustainable approach in deep hole drilling of Ti6Al4V: Effect of cryogenic cooling on hole parameters and its evaluation

The influence of the machining strategy on milling of polyetheretherketone (PEEK)

Study of milling process basics for the biocompatible PEEK material

Numerical and experimental investigation of orthogonal cutting of carbon fiber-reinforced polyetheretherketone (CF/PEEK)

Effect of 3D Printing Process Parameters and Heat Treatment Conditions on the Mechanical Properties and Microstructure of PEEK Parts

Effects of FDM parameters and annealing on the mechanical and tribological properties of PEEK

Experimental investigation on effect of tool geometry on thermal and crystallization characteristics in drilling of carbon fiber reinforced PEEK composite

Experiments on Machining Micro-Hole and Cutting Tool Failure Mechanism

Processing Parameter Effect, Formation Mechanism and Inhibition Method of Micro-Hole Exit Defects in Rotary Ultrasonic Pecking Drilling of SiCf/SiC Composites

Comparison of the performance of the internally cooled tool in closed circuit against standard PCBN tools in turning AISI D6 hardened

Evaluating the Effectiveness of PCD Tools on Machinability of Titanium Alloy Ti-6Al-4V in High Speed End Milling under Various Wet Cutting Conditions