Abstract:Considering the lower structural stiffness of titanium alloy thin-walled parts, the machining deformation defects were inevitable. In this paper, the theory and a series of experiments of liquid nitrogen (LN 2 ) cooled titanium alloy milling were executed in details. Based on cantilever sheet, a deflection calculation model of thin-walled parts subjected to milling force load was established considering cooling temperature. Compared with the conventional cooling milling strategy, the effects of LN 2 jet impingement on the deformation of milling area were analyzed. The results showed the deformation is related to the milling force, elastic modulus, and the milling point coordinates, and the cooling temperature has an effect on the milling deformation. At cryogenic, the milling force can only be increased by 10% compared with conventional cooling, but nearly 30% for the elastic modulus, as well as following the decreased deflection. At − 130 °C, the brittle chip fracture can be achieved, and the burr phenomenon on the machining surface is improved as well as the machining error. And the deformation of the milling area is decreased significantly. Meanwhile, the high speed milling can reduce the load of the free cutting parts. In addition, LN 2 can be achieved full boiling at the large flow of 35.5 L/h, and can quickly reduce the cooling temperature of cutting area and improve the heat transfer efficiency itself. The high milling speed and larger LN 2 flow can further improve the deformation defects of thin-walled parts. The cryogenic cooling strategy can change the chip breaking form, reduce the flexural deformation, increase the effective milling speed, and improve the milling system stiffness and the cutting heat transfer efficiency. They are the main reasons for the improvement of the deformation defects in thin-walled parts milling.

Tool wear and surface quality during milling CFRP laminates under dry and LN2-based cryogenic conditions

Machinability and Surface Quality During Milling CFRP Laminates Under Dry and Supercritical CO2-Based Cryogenic Conditions

Performance and mechanism evaluation during milling of CFRP laminates under cryogenic-based conditions

Experimental investigations of impact behavior and milling performance of T700-CFRP under cryogenic conditions

CFRP drilling under throttle and evaporative cryogenic cooling and micro-lubrication

Research on Tool Wear and Surface Integrity of CFRPs with Mild Milling Parameters

Effect of cooling and lubrication conditions on the variable angle milling of unidirectional CFRP with PCD Tools

Effect of Turning Parameter and Fiber Pullout on Machinability of Unidirectional EGFRP under Cryogenic Condition

Tool Wear and Surface Integrity of γ-TiAl Cryogenic Coolant Machining at Various Cutting Speed Levels

Surface morphology assessment of CFRP transverse grinding using CNT nanofluid minimum quantity lubrication

Deformation Resistance Performance of Carbon Fiber-Reinforced Plastic Machined by Controlling Drilling Area Temperature below the Glass Transition Temperature.

Wear Mechanism of Multilayer Coated Carbide Cutting Tool in the Milling Process of AISI 4340 under Cryogenic Environment

Experimental Study on Carbon Fiber-Reinforced Composites Cutting with Nanosecond Laser

Microstructural investigation and hole quality evaluation in S2/FM94 glass-fibre composites under dry and cryogenic conditions

Machinability and chip morphology evolution of hardened stainless steel using liquid nitrogen cryogenic

Interface properties of carbon fiber reinforced cyanate/epoxy resin composites at cryogenic temperature

Milling performance of cryogenic cooled titanium alloy thin-walled parts based on cantilever sheet

Tribological properties and tool wear in milling of in-situ TiB2/7075 Al composite under various cryogenic MQL conditions

Evaluation of new nano-cutting fluids for the processing of carbon fiber-reinforced composite materials

Tribological Properties of Carbon-Fibre-reinforced Plastic Against Tungsten Carbide under Dry Condition

Effect of Cryogenic Cooling on Cutting Surface Integrity and Surface Functional Properties of 6061 Aluminum Alloy