Abstract:Seven thousand and seventy‐five aluminum alloy is a typical aging reinforced alloy and has been used in many applications in the aerospace field, most of which are used as the main structural parts, so the research on its machining properties and corrosion resistance is significant. Considering that the microstructure of aging strengthened alloy will change after cryogenic treatment, it will certainly affect its machinability and corrosion resistance. This work aims to explore the effect of cutting parameters on the cutting force, surface quality, and corrosion resistance of 7075‐T6 aluminum alloy after and without cryogenic treatment. Cryogenically treated (T6‐C) and noncryogenically treated (T6) 7075‐T6 aluminum alloy samples are experimentally cut and electrochemically corroded in a 3.5% NaCl solution. SEM, EDS, and electrochemical analysis are carried out to examine how cutting parameters affect the cutting force, surface quality, and corrosion resistance of cryogenically treated 7075‐T6 aluminum alloy. The results show that after cryogenic treatment, under different cutting speeds, the cutting force is up to 39.8% smaller than without cryogenic treatment; under different cutting depths and feed rates, the cutting force is up to 136% and 21.54% smaller, respectively. Cryogenic treatment dramatically reduces the cutting force in the cutting process. As cutting speed increases, machined surface quality becomes better; fewer corrosion products and cracks are induced. When the cutting depth is 1.5 mm, there are fewer plows and micro‐cracks on the machined surface than under other parameters, but cutting depth does not affect corrosion morphology significantly. The size of corrosion products is up to 55 μm smaller. The electrochemical analysis finds that at the cutting speed of 1500 m/min, after cryogenic treatment, the current density is 59.4% smaller than without cryogenic treatment; polarization resistance is 1.68 × 105Ω•cm2 larger. At the cutting depth of 1.5 mm, after cryogenic treatment, the current density is 66.16% smaller; self‐corrosion potential shifts 0.19 V toward the positive pole. At the feed rate of 0.06 mm/z, after cryogenic treatment, self‐corrosion potential shifts 0.18 V toward the positive pole; polarization resistance is 10.7% larger. These parameters correspond to the best corrosion resistance.

Effect of Cryogenic Cooling on Cutting Surface Integrity and Surface Functional Properties of 6061 Aluminum Alloy

Effect of Cryogenic Cooling on Mechanical Properties and Cutting Force of 6061 Aluminum Alloy

Corrosion mechanism and machinability of 7075‐T6 aluminum alloy in high‐speed cutting: With and without cryogenic treatment

Effect of Cryogenic Treatment on Residual Stress and Microstructure of 6061 Aluminum Alloy and Optimization of Parameters

Effect of Cryogenic Treatments on Mechanical Properties of 2a11 Aluminum Alloy

Coupling effect of micro-textured tools and cooling conditions on the turning performance of aluminum alloy 6061

Investigation of machining property and sustainability performance of cryogenic turning of GH605 superalloy

Effect of Deep Cryogenic Treatment on the Artificial Aging Behavior of 6082 Aluminum Alloy

Tool Wear and Surface Integrity of γ-TiAl Cryogenic Coolant Machining at Various Cutting Speed Levels

Effect of Cryogenic Cooling on Micro-milling Properties of Titanium Alloy

Tough-brittle transition mechanism and specific cutting energy analysis during cryogenic machining of Ti–6Al–4V alloy

Relief of Residual Stresses in 7050 Aluminum Alloy by Deep Cryogenic Treatment

Effect of deep cryogenic treatment on microstructures and mechanical properties of automotive 6063Al alloy

Experiment and numerical study of chip formation mechanism during cryogenic machining of Ti-6Al-4V alloy

Cryogenic Deformation Behaviour of Aluminium Alloy 6061-T6

Research on Tool Wear and Machining Characteristics of TC6 Titanium Alloy with Cryogenic Minimum Quantity Lubrication (CMQL) Technology

Effect of Pretreatment and Cryogenic Temperatures on Mechanical Properties and Microstructure of Al-Cu-Li Alloy

Evolution of Mechanical Properties of Ti–6Al–4V Alloy in the Temperature Range of 20 to − 196 °C

Enhanced deep drawing formability and deformation mechanism of aluminum alloy at cryogenic temperature

Precision machining performance and mechanism of Ni/Ni 3 Al alloy under cryogenic temperature