Abstract:Ni-based superalloy GH4169 is widely demanded in the aerospace industry because of its excellent properties. However, the cutting of GH4169 at normal temperature has many challenges, such as tool wear, machining accuracy, and production efficiency. Cryogenic cutting has been an advanced method in assisting material removal machining. This paper focused on the cryogenic cutting performance of GH4169 at different initial temperatures, namely, 20 °C, −30 °C, −80 °C, and –130 °C. Firstly, the cryogenic mechanical properties of GH4169 were obtained by the Hopkinson pressure bar test at speed of 12 m/s and 18 m/s. The obtained data was used to analyze the cryogenic cutting performance of GH4169 at evaluated temperatures. The single factor milling experiments of GH4169 were carried out at room temperature and evaluated cryogenic levels, and the cutting performance in terms of cutting chips, cutting forces, and tool wear was investigated. The results showed that cryogenic cooling at −130 °C could increase the shear yield strength of the GH4169 by around 19.80% and the length of the cutting chip decreased monotonically by 53.45% compared with the length at room temperature. However, the cutting forces were not monotonically decreased. The cutting forces increased with the decrease of temperature when the initial temperature varied from 20 to −80 °C. However, when the initial temperature further dropped to –130 °C, the cutting forces were reduced by 30.60% for Fx, 24.02% for Fy, and 16.15% for Fz, respectively. Similarly, tool wear at the rake face and flank face is the most severe at –80 °C and the least at –130 °C. The average wear bandwidth at room temperature is 92.06 μm and decreases to 83.358 μm at –130 °C, which is reduced by 9.45%.

Investigation of machining property and sustainability performance of cryogenic turning of GH605 superalloy

Cryogenic Machining Performance and Surface Quality of Iron-Based Superalloy

Experimental Research on Turning Nickel-Based Superalloy GH4169 under Cryogenic Cooling Mixed Lubrication Jets

Tool wear and surface integrity in liquid nitrogen clean cutting of cobalt-based superalloy GH605 with AlTiN coated tools

Experimental Research on Cryogenic Cutting Performance of Ni-based Superalloy GH4169

Experimental study on cryogenic cooling tool wear of superalloy GH4169

Effect of Cryogenic Cooling on Cutting Surface Integrity and Surface Functional Properties of 6061 Aluminum Alloy

Application of minimum quantity GnP nanofluid and cryogenic LN 2 in the machining of Hastelloy C276

Tool Wear and Surface Integrity of γ-TiAl Cryogenic Coolant Machining at Various Cutting Speed Levels

Novel use of cryogenic cooling conditions in improving the machining performance of Al 8011/nano-SiC composites

Analytical and Experimental Investigation of the Nickel Based Superalloy Using Cryogenic Cooling Grinding

Heat Transfer Efficiency of Cryogenic-LN2 and CO2-snow and their application in the Turning of Ti-6AL-4V

Tribological properties and tool wear in milling of in-situ TiB2/7075 Al composite under various cryogenic MQL conditions

Sustainable milling of Ti–6Al–4V: A trade-off between energy efficiency, carbon emissions and machining characteristics under MQL and cryogenic environment

Effects of Cooling Air Temperature and Cutting Velocity on Cryogenic Machining of 1cr18ni9ti Alloy

Innovative Technology Investigation into Cryogenic Cooling Green Grinding Using Liquid Nitrogen Jet

Investigation of Machinability in Minimum Quantity Lubrication Milling of Gh4169 Aerospace Superalloy

The Effects of Cryogenic Cooling on Tool Wear and Chip Morphology in Turning of Tantalum-Tungsten Alloys Ta-2.5W

Tough-brittle transition mechanism and specific cutting energy analysis during cryogenic machining of Ti–6Al–4V alloy

Machinability and chip morphology evolution of hardened stainless steel using liquid nitrogen cryogenic

Effects of cooling air temperature on cryogenic machining of Ti–6Al–4V alloy