Abstract:An alternative to the existing method of processing secondary magnesium raw materials by remelting in a salt furnace can be distillation separation into volatile metals (Mg, Zn and Cd), low-volatile metals (Al, Mn and Zr) and rare earth elements. The separation of metals may be tracked based on phase diagrams where the field boundaries of the vapor–liquid equilibrium are plotted. Due to the fact that Mg, Zn and Cd have comparable saturated vapor pressures, the possibility of the distillation separation of Mg–Zn and Mg–Cd systems using full state diagrams including the melt–vapor phase transition boundaries were determined in this work. The boundaries of these systems were calculated based on the partial values of saturated vapor, determined by the boiling point method, and presented in the form of temperature–concentration dependencies with the indicated boundaries. The field boundaries were calculated (L + V) at atmospheric pressure (101.33 kPa) and in vacuum (1.33 kPa and 0.7 kPa,) supposing the implementation of the process. The possibility of the separate extraction of zinc and cadmium from magnesium was considered using complete phase diagrams including the boundaries of the melt–steam phase transition. When considering the boundaries of the vapor–liquid equilibrium in the binary systems Mg–Zn and Mg–Cd, it was established that it is impossible to separate metals in one "evaporation–condensation" cycle in a vacuum of 1.33 and 0.7 kPa. The problem is caused by the small size of the fields (L + V) at the temperature, which suggests processes of the re-evaporation of the condensate from the previous distillation stage. The separation of zinc and cadmium from liquid alloys with magnesium under equilibrium conditions requires several repetitions of the condensate distillation process. In non-equilibrium conditions, the real processes will require a larger number of conversions. This implies the expediency of the joint evaporation of magnesium with zinc and cadmium and the use of condensate for additional charging to liquid magnesium, and the remainder of the distillation, where volatile metals such as Al, Mn, Zr and rare earth elements will be concentrated, should be directed to the preparation of ligatures for special magnesium-based alloys.

The Separation Behavior of Impurities in the Purification of High-Purity Magnesium via Vacuum Distillation

Technical research on vacuum distillation to purify magnesium to 99.99% purity

Preparation of High-Purity Magnesium from Electrolytically Produced Crude Magnesium via Vacuum Distillation

One-step preparation of high purity magnesium by vacuum distillation technology

Preparation of high purity magnesium by vacuum gasification-directional condensation technology

Feasibility of Employing the Cooled Finger, a Fractional Crystallization Method for the Purification of Magnesium

Separation behavior of trace impurities during deep purification of zone-fused germanium tailings via vacuum distillation

Comparing Medium Pressure Dielectric Barrier Discharge (DBD) Plasmas and Classic Methods of Surface Cleaning/activation of Pure Mg for Biomedical Applications

On the Problem of the Distillation Separation of Secondary Alloys of Magnesium with Zinc and Magnesium with Cadmium

Distribution of impurities in magnesium via silicothermic reduction

Recovery of AZ91D magnesium alloy waste by vacuum gasification - Directed condensation

A method of removal of nickel impurity from electrolytic magnesium

Development of a novel strategy for the quantification of ultra-trace impurity elements in high-purity magnesium using inductively coupled plasma tandem mass spectrometry

A review of preparing high-purity metals by vacuum distillation

The impurities distribution and purification efficiency of high-purity aluminum preparation by zone melting in vacuum

Research status and prospects of melt refining and purification technology of magnesium alloys

A Study on the Removal of Impurity Elements Silicon and Zinc from Rubidium Chloride by Vacuum Distillation

Novel and efficient purification of scrap Al-Mg alloys using supergravity technology

Behavior of Impurity Elements in Pure Gadolinium During Ultra-High Purification

Research on the Removal of Impurity Elements During Ultra-High Purification Process of Terbium

High- and Ultra-High-Purity Aluminum, a Review on Technical Production Methodologies