Abstract:Besides conventional structuring processes such as turning, milling or photo-chemical etching, laser processes are increasingly being used for surface structuring of metals. These laser processes differ fundamentally in that structuring is carried out either by material removal or by material redistribution. In this study, a new hybrid process of material ablation by means of pulsed laser radiation and material redistribution based on a remelting process by means of cw laser radiation is experimentally investigated. Besides an introduction to this new hybrid process, we give a detailed description of the equipment and methods used as well as surface structures produced on Ti6Al4V. A melt pool was generated on a prepared Ti6Al4V surface using cw laser radiation with a laser beam diameter of 520 mu m, laser power of 220 W, and a scanning velocity of 100 mm/s. In order to create surface structures, simultaneously, superimposed pulsed laser radiation with a laser beam diameter of 65 mu m, pulse duration of 60 ns, a maximum pulse energy of 0.35 mJ, and a pulse frequency of 50 kHz was used to evaporate small amounts of molten material from the melt pool. This localized evaporation of molten material is assumed to create vapor pressure that deforms the melt pool surface and therefore leads to surface structures. Our results indicate that by pulsed laser radiation capillary surface waves with a wavelength of the doubled laser beam diameter are excited on the melt pool surface. This forced excitation of capillary surface waves result in surface structures that are analyzed after solidification by means of white light interferometry. Based on this analysis we derived an oscillation frequency of v = 2.27 (+/- 0.16) kHz for the excited capillary surface wave as well as an effective kinematic viscosity of mu= 0.1328 cm(2)s(-1) for the damping of this surface oscillation during solidification. In terms of structural features, we achieved surface structures with heights of up to 100 mu m. Furthermore, structure height controllably scales in dependence on pulse energy and number of laser pulses as long as no ejection of molten material takes place. Finally, a comparison of the redistributed material volume per time shows that we achieved a volume redistribution rate of 28.37 mm(3)/min, which is significantly bigger than has been achieved with other laser texturing techniques so far and demonstrates the high potential of this new hybrid technique not only for surface structuring purposes.

Modeling The Microrelief Structure of Ti6Al4V Titanium Alloy Surface After Exposure to Femtosecond Laser Pulses

Influence of Power and Frequency in the Femtosecond Laser Texturing of Ti6Al4V

Comprehensive ablation study of near-IR femtosecond laser action on the titanium-based alloy Ti6Al4V: morphological effects and surface structures at low and high fluences

Influence of femtosecond laser pulse sequence on the morphology and roughness of titanium surface micro-patterns

Numerical Simulation of Effect of Different Initial Morphologies on Melt Hydrodynamics in Laser Polishing of Ti6Al4V

Investigations on femtosecond laser-induced surface modification and periodic micropatterning with anti-friction properties on Ti6Al4V titanium alloy

Microstructure Formations Resulting from Nanosecond and Picosecond Laser Irradiation of a Ti-Based Alloy under Controlled Atmospheric Conditions and Optimization of the Irradiation Process

Experimental Investigation on a New Hybrid Laser Process for Surface Structuring by Vapor Pressure on Ti6Al4V

Influence of Femtosecond Laser Surface Modification on Tensile Properties of Titanium Alloy

Mechanical Properties and Residual Stress Measurements of Grade IV Titanium and Ti-6Al-4V and Ti-13Nb-13Zr Titanium Alloys after Laser Treatment

Formation, evolution and characterization of nanoporous structures on the Ti6Al4V surface induced by nanosecond pulse laser irradiation

Characterization of Ti6Al4V Alloy Produced by Laser-Powder Bed Fusion and Surface Modification Using Nanosecond Laser

Microstructure and Hardness of the Laser Surface Treated Titanium

Biocompatibility of micro/nano structures on the surface of Ti6Al4V and Ti-based bulk metallic glasses induced by femtosecond laser

Effects of Different Laser Shock Processes on the Surface Morphology and Roughness of TC4 Titanium Alloy

On interaction between laser and Ti6Al4V titanium alloy

Finite element simulation and experimental study of single-laser track in laser polishing of Ti6Al4V

Preparation of Microstructure Laser Ablation and Multiple Acid-Etching Composites on the Surfaces of Medical Titanium Alloy TC4 by Laser Ablation and Multiple Acid-Etching, and Study of Frictional Properties of the Processed Surfaces

Mechanical Surface Treatment of Titanium Alloy Ti6Al4V Manufactured by Direct Metal Laser Sintering Using Laser Cavitation

Femtosecond laser modification of titanium surfaces: direct imprinting of hydroxylapatite nanopowder and wettability tuning via surface microstructuring

Surface and microstructure modifications of Ti-6Al-4V titanium alloy cutting by a water jet/high power laser converging coupling