Abstract:Besides conventional structuring processes such as turning, milling or photo-chemical etching, laser processes are increasingly being used for surface structuring of metals. These laser processes differ fundamentally in that structuring is carried out either by material removal or by material redistribution. In this study, a new hybrid process of material ablation by means of pulsed laser radiation and material redistribution based on a remelting process by means of cw laser radiation is experimentally investigated. Besides an introduction to this new hybrid process, we give a detailed description of the equipment and methods used as well as surface structures produced on Ti6Al4V. A melt pool was generated on a prepared Ti6Al4V surface using cw laser radiation with a laser beam diameter of 520 mu m, laser power of 220 W, and a scanning velocity of 100 mm/s. In order to create surface structures, simultaneously, superimposed pulsed laser radiation with a laser beam diameter of 65 mu m, pulse duration of 60 ns, a maximum pulse energy of 0.35 mJ, and a pulse frequency of 50 kHz was used to evaporate small amounts of molten material from the melt pool. This localized evaporation of molten material is assumed to create vapor pressure that deforms the melt pool surface and therefore leads to surface structures. Our results indicate that by pulsed laser radiation capillary surface waves with a wavelength of the doubled laser beam diameter are excited on the melt pool surface. This forced excitation of capillary surface waves result in surface structures that are analyzed after solidification by means of white light interferometry. Based on this analysis we derived an oscillation frequency of v = 2.27 (+/- 0.16) kHz for the excited capillary surface wave as well as an effective kinematic viscosity of mu= 0.1328 cm(2)s(-1) for the damping of this surface oscillation during solidification. In terms of structural features, we achieved surface structures with heights of up to 100 mu m. Furthermore, structure height controllably scales in dependence on pulse energy and number of laser pulses as long as no ejection of molten material takes place. Finally, a comparison of the redistributed material volume per time shows that we achieved a volume redistribution rate of 28.37 mm(3)/min, which is significantly bigger than has been achieved with other laser texturing techniques so far and demonstrates the high potential of this new hybrid technique not only for surface structuring purposes.

Surface and microstructure modifications of Ti-6Al-4V titanium alloy cutting by a water jet/high power laser converging coupling

Experimental Research and Optimization of Ti-6Al-4V Alloy Microgroove Machining Based on Waterjet-Guided High-Power Laser

Experimental Investigation on a New Hybrid Laser Process for Surface Structuring by Vapor Pressure on Ti6Al4V

Improving Superficial Microstructure and Properties of the Laser-Processed Ultrathin Kerf in Ti-6Al-4V Alloy by Water-Jet Guiding

Laser surface modification of Ti--6Al--4V: wear and corrosion characterization in simulated biofluid

Surface oxidation and phase transformation of the stainless steel by hybrid laser-waterjet impact

Experimental Comparison of the Microstructure and Surface Roughness in CO2 Laser Cutting of the Titanium Alloy Ti–6Al–4V and the Pure Titanium Ti

Microstructure and Properties of Ti6Al4V Surface Processed by Continuous Wave Laser in Different Atmospheres

Microstructural evolution, mechanical properties and surface quality of TC11 titanium alloy subjected to waterjet-assisted laser direct inscription

Investigation of the Effect of Laser Cutting Parameters on Surface and Kerf Quality of Thick Ti–6Al–4V Alloy Sheets

Superhydrophobic Surface Preparation and Wettability Transition of Titanium Alloy with Micro/Nano Hierarchical Texture

Mechanical Surface Treatment of Titanium Alloy Ti6Al4V Manufactured by Direct Metal Laser Sintering Using Laser Cavitation

Laser Cutting of Titanium Alloy Plates: A Review of Processing, Microstructure, and Mechanical Properties

Influence of Power and Frequency in the Femtosecond Laser Texturing of Ti6Al4V

Experimental investigation on surface characteristics of Ti6Al4V alloy during abrasive water jet machining process

Investigations on femtosecond laser-induced surface modification and periodic micropatterning with anti-friction properties on Ti6Al4V titanium alloy

The effect of laser surface re-melting on the surface roughness and micro-hardness of selective laser melting (SLM) fabricated Ti-6Al-4V samples

The Interplay of Thermal Gradient and Laser Process Parameters on the Mechanical Properties, Geometrical and Microstructural Characteristics of Laser-Cladded Titanium (Ti6Al4V) Alloy Composite Coatings

Enhancing orthogonal finishing machining of Ti6Al4V with laser-ablated tool geometry modifications

Microstructural Strengthening and Plastic Degradation of Ti–6Al–4V Induced by Laser Ablation

Formation, evolution and characterization of nanoporous structures on the Ti6Al4V surface induced by nanosecond pulse laser irradiation