Abstract:The mechanism analysis of the interface characteristics of sequential co-injection self-reinforced parts starts from the following three aspects. Firstly, the formation process of the bonding interface and the factors affecting the bonding strength were investigated in theory. A theoretical model of interface bonding degree, which explains the bonding degree of the interface by the penetration depth of polymer chains through the initial solid-melt interface, was proposed, and then combines the average critical penetration depth to analyze the influence of different molding parameters on the interface bonding degree. Then, the interface bonding strength of the prepared polypropylene sequential co-injection self-reinforced parts under different molding parameters (including melt temperature, mold temperature and injection speed, etc.) was studied experimentally, and the reliability of the model was verified. Finally, the interrelationship function between effective penetration degree of molecular chain diffusion and interface bonding degree on both sides of the interface is established, which provides a new theoretical basis for interfacial mechanism analysis of sequential co-injection self-reinforced parts. The results show that the interface bonding degree between experiment and theory has a good consistency, and the deviation between them is within 10%, which proves that the theoretical model is reliable. In addition, the theoretical critical penetration depth and the theoretical maximum degree of bonding sequential co-injection polypropylene products are 1.399 nm and 0.857, respectively. The performance test results of different molding parameters show that the temperature change of reinforced melt is the key factor affecting the interfacial fusion of sequential co-injection self-reinforced parts. The high temperature melt is beneficial to the diffusion and intertwining of molecular chains on both sides of the interface and to the improvement of the degree of interfacial bonding.

Enhanced Adhesion Properties of Polymer-Metal Interfaces via Nano-injection Molding: A Study on Molecular Kinematic Mechanisms

Study on the interfacial interactions and adhesion behaviors of variouspolymer-metalinterfaces in nano molding

The polymer-metal interactive behavior in polyphenylene sulfide/aluminium hetero interface in nano injection molding

Molecular dynamics simulation study of the joining strength of different polymer‐aluminum heterointerfaces in nano‐injection molding

Effect of polydopamine surface modification on the adhesive properties of nano‐injection molded metal‐polymer interfaces: A molecular dynamics simulation study

Simulating the Replication and Entanglement of Semi-Rigid Polymers in Nano-Injection Moulding

Effect of the Polymer on the Joint Strength of Polymer/copper Hybrids Produced by Nano-Injection Molding: Comparison of Polybutylene Terephthalate and Polyphenylene Sulfide Via Experimental and Computational Methods

Interfacial Nanoconnections and Enhanced Mechanistic Studies of Metallic Coatings for Molecular Gluing on Polymer Surfaces.

Effects of Polybutylene Terephthalate Molecular Weight and Nanostructure Size of Copper Surface on Replication Quality of Nano-Injection Molding under Practical Condition: A Molecular Simulation Study

Aluminum/polypropylene composites produced through injection molding

Experimental Investigation and Molecular Dynamics Simulation on the Anti-Adhesion Behavior of Alkanethiols on Nickel Insert in Micro Injection Molding

Interfacial Interaction and Joining Property of Direct Injection-Molded Polymer-Metal Hybrid Structures: A Molecular Dynamics Simulation Study

Direct Bonding of Polypropylene to Aluminum Using Molecular Connection and the Interface Nanoscale Properties

Atomistic simulation of metal-polymer adhesion

Interface needle structure induced high-performance aluminum alloy/PPS hybrids

Spatial Hierarchy and Interfacial Structure in Injection-Molded Bars of Polypropylene-Based Blends and Composites

Surface Wettability and Tribological Performance of Ni-based Nanocomposite Moulds against Polymer Materials

A Facile Nano-Tio2 Coating Effectively Enhancing the Microscopic Properties of Metal-Polymer Interface

A Method of Predicting Effective Interface Properties of Polymer-Metal Hybrid Structures by Molecular Dynamics

Reinforcement of solid-melt interfaces for semicrystalline polymers in a sequential two-staged injection molding process

Mechanism Analysis of Interface Characteristics of Sequential Co-injection Self-Reinforced Parts