Abstract:Electron beam selective melting (EBSM), is powder bed fusion additive manufacturing (AM) technique by adding materials layer upon layer. The capacity of EBSM to fabricate complex and multi-functional parts has made it a realm of great interest for researchers in the domain of science. However, during the fabrication of functionally graded materials (FGMs) with graded composition by EBSM using at least two different materials, it is difficult to separate and reuse these materials after the fabrication. Additionally, it is difficult to vary the powder composition within a layer to fabricate a horizontal graded structure. In this research, an element evaporation concept based on electron beam powder bed fusion, is presented for fabricating one-dimensional (1D) FGMs of (α2 + γ) TiAl alloy/(α + β) titanium alloy from a single material powder. By irradiating different sub-regions of the powder bed with electron beam energy input of different magnitude to greatly reduce the relative atomic ratio of aluminum from 47% to less than 10%, the 1D FGMs structures with (α2 + α + β) phases in the interfacial transition zone (ITZ) were successfully produced. Since the microstructure of the ITZ has a significant effect on mechanical properties for the 1D FGMs, three different overlap scan distances (0.5, 1.0 and 2.0 mm), which result in different ITZs, were utilized for evaluating the microstructure of the ITZ and resulting mechanical properties. The results showed that no defects were found in the specimens of any overlap distance. Moreover, the width of the ITZ increases as the overlap scan distance, and the tensile strength decreases with the overlap scan distance.

Functionally Graded Material Production and Characterization using the Vertical Separator Molding Technique and the Powder Metallurgy Method

Synthesis of Functionally Graded AA7075-B4C Composite with Multi-Level Gradient Structure

Composition design and mechanical properties of B 4 C/Al-Zn-Mg-Cu functionally graded materials prepared by laser additive manufacturing

Characterization of a functionally graded material produced using a new designed blender

Fabrication and Ballistic Performance Evaluation of B4C/AA7075 Functionally Graded Materials for Armor Applications

Effect of graded microstructure on the modulus, hardness, and strength of hot-pressed ZrB2-B4C FGM

Fabrication of functionally graded materials from a single material by selective evaporation in electron beam powder bed fusion

Evaluation of the mechanical and microstructural properties of an Al7075/B4C/Gr FGM plate fabricated using a stir casting process

Characterization of Interfacial Transition Zone of Functionally Graded Materials with Graded Composition from a Single Material in Electron Beam Powder Bed Fusion

Microstructure and Mechanical Properties of P21-STS316L Functionally Graded Material Manufactured by Direct Energy Deposition 3D Print

Influence of gradation in the reinforcement particles on the interfacial microstructure and mechanical properties of functionally graded composites

Fabrication process of smooth functionally graded materials through a real-time inline control of the component ratio

Laser Powder Bed Fusion of Functionally Graded Bi-Materials: Role of VC on Functionalizing AISI H13 Tool Steel

Preparation and characterization of Al2O3–Ti3SiC2 composites and its functionally graded materials

Effect of Silicon Carbide Weight Percentage and Number of Layers on Microstructural and Mechanical Properties of Al7075/SiC Functionally Graded Material

A review on fabrication and characteristics of functionally graded aluminum matrix composites fabricated by centrifugal casting method

Layer-level fabrication of continuous functionally graded materials (cFGMs) via Powder Bed Fusion – Laser Beam technology

Preparation and investigation of microstructure and wear properties of functionally graded materials of Aluminum-Nickel alloys

Fabrication and characterization of stainless steel 308 L / Inconel 625 functionally graded material with continuous change in composition by dual-wire arc additive manufacturing

Evaluation of mechanical properties of Ni/BaTiO3 functionally graded material

A novel approach for developing boron carbide (B4C)/cyanate ester (CE) co-continuous Functionally Graded Materials (FGMs) with eliminated abrupt interfaces