Abstract:In this contribution, Automat FOR Simulation of HETero-structures v2.5 software was used for unveiling the photovoltaic performance and thermal stability of relatively less explored TiO 2 /c-Si heterojunction solar cell architecture based on 110 μm wafers. Firstly, the dependence of the photovoltaic performance on the emitter layer, i.e. the TiO 2 layer, was explored by varying its different characteristics: thickness, carrier concentration and the defect density at the TiO 2 /Si interface. The study revealed that the power conversion efficiency might be as high as 16.34% (even without any interfacial passivation layer) even when the thickness of the wafer was kept at 110 μm; the thickness and the doping concentration of the TiO 2 emitter layer were kept as 7 nm and 1 × 10 20 cm −3 ; respectively. The corresponding defect density at the TiO 2 /p-Si interface was 1 × 10 12 cm −2 . Furthermore, a significant gain in the power output was realized by embedding either poly-silicon on oxide or carrier selective contact layer at the rear side of the device architecture. In the case of the incorporation of poly-silicon on the oxide structure at the rear side of the metal/c-Si interface, the role of the ultra-thin tunnel oxide thickness on the device's performance was explored in detail. Next, the poly-silicon on oxide structure was replaced by the NiO x layer, an efficient hole transport layer at the rear side of the device architecture. Various performance-affecting parameters, such as NiO x thickness, NiO x band gap, and the defect density at the NiO x /Si interface, were varied at different carrier concentrations of the NiO x layer to obtain the best possible conditions for realizing the maximum power output. The study was further extended to examine the influence of the wafer lifetime on the device performance of all the simulated solar cells. Eventually, the device temperature was varied from 275 to 375 K with an interval of 25 K to investigate the thermal stability of the proposed cell architectures so that the best possible architecture could be selected for practical fabrication both in terms of photovoltaic performance and thermal stability.

ON THE PERFORMANCE LIMITS FOR MONO CRYSTALLINE SILICON SOLAR CELLS: A COMPARATIVE STUDY

Optimization of Mono-Crystalline Silicon Solar Cell Devices Using PC1D Simulation

An In-Depth Analysis of the Silicon Solar Cell Key Parameters’ Optimal Magnitudes Using PC1D Simulations

Electrical performance analysis and optimization of monofacial and bifacial crystalline silicon solar cells

Numerical simulation based performance enhancement approach for an inorganic BaZrS3/CuO heterojunction solar cell

Numerical Simulation of the Performance of Sb2Se3 Solar Cell via Optimizing the Optoelectronic Properties Based SCAPS-1D

Development of the Monolayer Silicon Solar Cell Based on Photonic Crystals

A Comparative Study of Quantum Dot Solar Cell with Two Different ETLs of WS2 and IGZO Using SCAPS-1D Simulator

Characterization and optimization of high-efficiency crystalline silicon solar cells

Optimization of intrinsic layer thickness, dopant layer thickness and concentration for a-SiC/a-SiGe multilayer solar cell efficiency performance using Silvaco software

Numerical analysis of ultra-thin MASnI3 based perovskite solar cell by SCAPS-1D

Numerical Simulation of C-V and I-V Characteristics of Perovskite Based Solar Cells

Analysis of Advanced TiO2/Si based Solar Cell Architecture: Improving PV Parameters and Thermal Stability

Numerical Investigation of CuSbS2Thin Film Solar Cell using SCAPS-1D: Enhancement of Efficiency on Experimental Films by Defect Studies

Investigation of low band gap silicon alloy thin film solar cell for improving short and long wavelength response

Numerical Design of Ultrathin Hydrogenated Amorphous Silicon-Based Solar Cell

Systematic Modeling and Optimization for High‐Efficiency Interdigitated Back‐Contact Crystalline Silicon Solar Cells

On performance of thin-film meso-structured perovskite solar cell through experimental analysis and device simulation

Monolithic perovskite/c-Si tandem solar cell: Progress on numerical simulation

Elucidating the Effects of Interconnecting Layer Thickness and Bandgap Variations on the Performance of Monolithic Perovskite/Silicon Tandem Solar Cell by wxAMPS

Study of Black Silicon Wafer through Wet Chemical Etching for Parametric Optimization in Enhancing Solar Cell Performance by PC1D Numerical Simulation