Abstract:In this study, a novel perovskite solar cell (PSC) architecture is presented that utilizes an HTL-free configuration with formamide tin iodide (FASnI3) as the active layer and fullerene (C60) as the electron transport layer (ETL), which represents a pioneering approach within the field. The elimination of hole transport layers (HTLs) reduces complexity and cost in PSC heterojunction structures, resulting in a simplified and more cost-effective PSC structure. In this context, an HTL-free tin HC(NH2)2SnI3-based PSC was simulated using the solar cell capacitance simulator (SCAPS) within a one-dimensional framework. Through this approach, the device performance of this novel HTL-free FASnI3-based PSC structure was engineered and evaluated. Key performance parameters, including the open-circuit voltage (Voc), short-circuit current density (Jsc), fill factor (FF), power conversion efficiency (PCE), I-V characteristics, and quantum efficiency (QE), were systematically assessed through the modulation of physical parameters across various layers of the device. A preliminary analysis indicated that the HTL-free configuration exhibited improved I-V characteristics, with a PCE increase of 1.93% over the HTL configuration due to improved electron and hole extraction characteristics, reduced current leakage at the back contact, and reduced trap-induced interfacial recombination. An additional boost to the device's key performance parameters has been achieved through the further optimization of several physical parameters, such as active layer thickness, bulk and interface defects, ETL thickness, carrier concentration, and back-contact materials. For instance, increasing the thickness of the active layer PSC up to 1500 nm revealed enhanced PV performance parameters; however, further increases in thickness have resulted in performance saturation due to an increased rate of hole-electron recombination. Moreover, a comprehensive correlation study has been conducted to determine the optimum thickness and donor doping level for the C60-ETL layer in the range of 10-200 nm and 1012-1019 cm-3, respectively. Optimum device performance was observed at an ETL-C60 ultra-thin thickness of 10 nm and a carrier concentration of 1019 cm-3. To maintain improved PCEs, bulk and interface defects must be less than 1016 cm-3 and 1015 cm-3, respectively. Additional device performance improvement was achieved with a back-contact work function of 5 eV. The optimized HTL-free FASnI3 structure demonstrated exceptional photovoltaic performance with a PCE of 19.63%, Voc of 0.87 V, Jsc of 27.86 mA/cm2, and FF of 81%. These findings highlight the potential for highly efficient photovoltaic (PV) technology solutions based on lead-free perovskite solar cell (PSC) structures that contribute to environmental remediation and cost-effectiveness.

Elucidating the Effects of Interconnecting Layer Thickness and Bandgap Variations on the Performance of Monolithic Perovskite/Silicon Tandem Solar Cell by wxAMPS

Investigating the influence of the counter Si-cell on the optoelectronic performance of high-efficiency mono-lithically perovskites/silicon tandem cells under various optical sources

The influence of the interface layer between the electron transport layer and absorber on the performance of perovskite solar cells

Optimizing tandem solar cells efficiency through current matching technique in lead-free perovskite/c-Si and lead-free perovskite/CIGS absorbers

Interface engineering and defect passivation for enhanced hole extraction, ion migration, and optimal charge dynamics in both lead-based and lead-free perovskite solar cells

Light Management Enhancement for Four-Terminal Perovskite-Silicon Tandem Solar Cells: The Impact of the Optical Properties and Thickness of the Spacer Layer between Sub-Cells

Influence of Contact Electrode and Light Power on the Efficiency of Tandem Perovskite Solar Cell: Numerical Simulation

Modeling and numerical simulation of high efficiency perovskite solar cell with three active layers

Advanced Optoelectronic Modeling and Optimization of HTL-Free FASnI3/C60 Perovskite Solar Cell Architecture for Superior Performance

Tuning of the Interconnecting Layer for Monolithic Perovskite/Organic Tandem Solar Cells with Record Efficiency Exceeding 21%

Enhanced optoelectronic coupling for perovskite-silicon tandem solar cells

Strategic integration of electron transport layer for high-performance optimized lead-free double perovskite solar cells with temperature dependence

Effect of 3,4,9,10-Perylenetetracarboxylic Bisbenzimidazole (ptcbi) As Well As Bathocuproine (bcp) and Ag Interlayer Thickness on the Performance of Organic Tandem Solar Cells

Efficient Monolithic Perovskite-Si Tandem Solar Cell Enabled by an Ultra-Thin Indium Tin Oxide Interlayer

Optical Design of Monolithic Two-Terminal Perovskite/Si Tandem Solar Cells for Efficient Photon Management

Efficient Light Management in a Monolithic Tandem Perovskite/Silicon Solar Cell by Using a Hybrid Metasurface

Multifunctional Buffer Layer Engineering for Efficient and Stable Wide‐Bandgap Perovskite and Perovskite/Silicon Tandem Solar Cells

Optoelectronic Coupling of Perovskite/Silicon Heterojunction Tandem Solar Cell by SCAPS Simulation

Computational Study of Ternary Devices: Stable, Low-Cost, and Efficient Planar Perovskite Solar Cells

Enhanced efficiency of bifacial perovskite solar cells using computational study

Molecular engineering of hole-selective layer for high band gap perovskites for highly efficient and stable perovskite-silicon tandem solar cells