Abstract:Interfacial engineering is critical for highly efficient charge carrier transport in perovskite solar cells (PSCs). Herein, we developed a new method, called successive surface engineering, that affords PSCs with enhanced efficiency and dramatically suppressed current-voltage hysteresis. Upon modifying the TiO2 compact layer, which is commonly used as an electron transport layer (ETL) in regular-structure (n-i-p) planar heterojunction (PHJ) PSCs, by successively incorporating [6,6]-phenyl-C-61-butyric acid methyl ester (PC61BM) and an ethanolamine (ETA)-functionalized fullerene (C-60-ETA) synthesized facilely via a one-pot nucleophilic addition reaction, the average power conversion efficiency (PCE) of the CH3NH3PbI3-based PHJ-PSC devices increased from 13.00% to 16.31%; the best PCE attained was 18.49%, which, to our knowledge, represents the highest PCE reported to date for regular-structure PHJ-PSCs devices based on fullerene-modified TiO2 interlayers. In contrast, single surface engineering of the TiO2 layer with a PC61BM or C-60-ETA layer alone results in only negligible changes in PCE, revealing the synergistic effect of these two fullerene derivatives: the PC61BM layer can passivate the traps on the TiO2 surface, while the subsequent C-60-ETA layer not only improves the wettability of the perovskite film on the ETL but also facilitates electron transport across the interface between the perovskite and the TiO2 ETL. The structural and morphological characterizations show that following dual surface modification of the TiO2 layer with PC61BM and C-60-ETA, both the surface coverage and crystallinity of the CH3NH3PbI3 perovskite film are improved. Steady-state photoluminescence decay and electrochemical impedance spectroscopic studies manifest that the dual surface modification substantially improves the charge extraction efficiency and suppresses charge recombination. As a consequence, this dual surface modification leads to an obvious increase of the short-circuit current density (J(sc)), which contributes primarily to the PCE enhancement. Additionally, because PC61BM may induce passivation of the traps on the TiO2 surface and in the perovskite layer, remarkably, the hysteresis of the current-voltage response is dramatically suppressed following the dual surface modification.

Effect of 3,4,9,10-Perylenetetracarboxylic Bisbenzimidazole (ptcbi) As Well As Bathocuproine (bcp) and Ag Interlayer Thickness on the Performance of Organic Tandem Solar Cells

Study on the influence of embedded structure of carbon quantum dots of the organic solar cells with the territory active layer structure of P3HT: PC 61 BM: CQDs

Improving the Performance of Polymer Solar Cells with Benzo[ghi]perylenetriimide-Based Small-Molecules as Interfacial Layers

Optical simulation and experimental determination of the effect of subcell sequence in tetraphenyldibenzoperiflanthene- and phthalocyanine-based tandem solar cells

The Dependence of the Cathode Architecture on the Photoactive Layer Morphology in Bulk-Heterojunction Polymeric Solar Cells

Highly Efficient Organic Tandem Solar Cell with a SubPc Interlayer Based on TAPC:C70 Bulk Heterojunction

A ternary organic electron transport layer for efficient and photostable perovskite solar cells under full spectrum illumination

Successive Surface Engineering Of Tio2 Compact Layers Via Dual Modification Of Fullerene Derivatives Affording Hysteresis-Suppressed High-Performance Perovskite Solar Cells

Synergic Interface and Optical Engineering for High‐Performance Semitransparent Polymer Solar Cells

Simultaneous Performance and Stability Improvement of Ternary Polymer Solar Cells Enabled by Modulating the Molecular Packing of Acceptors

Improved Efficiency and Stability in Polymer Solar Cells Using a Tetra-nuclear Zinc(II) Complex Interfacial Layer

Organic Photovoltaics Incorporating Electron Conducting Exciton Blocking Layers

Restricting The Liquid-Liquid Phase Separation Of Ptb7-Th:Pf12tbt:Pc71bm By Enhanced Ptb7-Th Solution Aggregation To Optimize The Interpenetrating Network

The Study on Organic Solar Cells Based on Bathocuproine As an Exciton Blocking Layer

Achieving over 11% Power Conversion Efficiency in PffBT4T-2OD-based Ternary Polymer Solar Cells with Enhanced Open-Circuit-voltage and Suppressed Charge Recombination

Layer-by-Layer-Processed Ternary Organic Solar Cells Using Perylene Bisimide As a Morphology-Inducing Component.

Efficient polymer solar cells utilizing solution-processed interlayer based on different conjugated backbones

Effect of buffer layers on the performance of organic photovoltaic cells based on copper phthalocyanine and C60

High Efficiency Non-fullerene Organic Tandem Photovoltaics Based on Ternary Blend Subcells

Performance Optimization by Considering Current Matching in Polymer Tandem Solar Cells

Elucidating the Roles of TiCl4 and PCBM Fullerene Treatment on TiO2 Electron Transporting Layer for Highly Efficient Planar Perovskite Solar Cells