Abstract:Despite the rapid progress that has been made in increasing the power conversion efficiency (PCE) of organic solar cells (OSCs) over the past decade, it is a challenge to realize efficient and environment-friendly OSCs. In this contribution, all polymer solar cells were fabricated with a blend of poly[4,8-bis(5-(2-ethylhexyl) thiophen-2-yl) benzo[1,2-b: 4,5-b'] dithiophene-co-3-fluorothieno[3,4-b] thiophene-2-carboxylate] (PTB7Th) donor and vinylene-bridged perylenediimide-based polymer (PDI-V) acceptor, in which non-halogenated tetrahydrofuran (THF) was used as the host solvent. A conventional device structure of ITO/poly(3,4-ethylenedioxythiophene): poly(styrenesulfonate) (PEDOT:PSS)/PTB7-Th:PDI-V/zirconium acetylacetonate (ZrAcac)/Al was employed, where PEDOT:PSS functioned as the hole transporting layer (HTL) and ZrAcac functioned as the electron transporting layer (ETL). The mixed solution of PTB7-Th and PDI-V was spin cast on the top of PEDOT:PSS layer to form the active layer. After that, ZrAcac solution was spin cast on the top of PTB7-Th:PDI-V layer. Different thermal annealing temperatures were used to optimize the active layer morphology. In details, OSCs without thermal annealing showed a PCE of 7.1%, with a short-circuit current (J(SC)) of 14.9 mA/cm(2), an open-circuit voltage (V-OC) of 0.74 V, and a fill factor (FF) of 64%. The devices annealed at 120 degrees C showed a high PCE of 8.1% with a J(SC) of 15.5 mA/cm(2), a V-OC of 0.74 V, and a FF of 70%. Further increasing the annealing temperature to 150 degrees C led to decreased FF and thereby a relatively lower PCE (7.4%). To the best of our knowledge, the PCE of similar to 8.1% is one of the highest PCE values reported in the literature so far for all polymer solar cells. The high and balanced hole and electron mobility partially contributed to such a high performance. These results suggest that THF as good non-halogenated solvent can be used to fabricate high-performance all polymer solar cells. Higher efficiency can be achieved for OSCs with THF solvent when better polymer acceptors are employed.

Alcohol/Water-Soluble Porphyrins As Cathode Interlayers in High-Performance Polymer Solar Cells

Application of a Water-Soluble Metallophthalocyanine Derivative As a Cathode Interlayer for the Polymer Solar Cells

[6,6]-Phenyl-c61-butyric Acid 2-((2-(dimethylamino)ethyl)(methyl)amino)-ethyl Ester As an Acceptor and Cathode Interfacial Material in Polymer Solar Cells

A Series of Porphyrins As Interfacial Materials for Inverted Perovskite Solar Cells

Improved Efficiency and Stability in Polymer Solar Cells Using a Tetra-nuclear Zinc(II) Complex Interfacial Layer

Physically Adsorbed Fullerene Layer on Positively Charged Sites on Zinc Oxide Cathode Affords Efficiency Enhancement in Inverted Polymer Solar Cell.

Efficiency Enhancement for Bulk Heterojunction Photovoltaic Cells Via Incorporation of Alcohol Soluble Conjugated Polymer Interlayer

A New Alcohol‐Soluble Polymer PFN‐ID as Cathode Interlayer to Optimize Performance of Conventional Polymer Solar Cells by Increasing Electron Mobility

Efficient and stable perovskite solar cells through electrochemically polymerized porphyrin-based hole-transporting materials

Improving the Performance of Polymer Solar Cells with Benzo[ghi]perylenetriimide-Based Small-Molecules as Interfacial Layers

Designing Thickness-Insensitive Cathode Interlayers via Constructing Noncovalently Conformational Locks for Highly Efficient Non-fullerene Organic Solar Cells

Nonconjugated Self-Doped Polymer Zwitterions as Efficient Interlayers for High Performance Organic Solar Cells

Phenol‐Functionalized Perylene Bisimides as Amine‐Free Electron Transporting Interlayers for Stable Nonfullerene Organic Solar Cells

Bilayer Structured Supramolecular Light Harvesting Arrays Based on Zinc Porphyrin Coordination Polymers for Enhanced Photocurrent Generation in Dye Sensitized Solar Cells

Ester‐Functionalized Polythiophene Interlayers for Enhanced Performance and Stability of Perovskite Solar Cells

Highly Efficient Polymer Solar Cells Based on a Universal Cathode Interlayer Composed of Metallophthalocyanine Derivative with Good Film-Forming Property

Thermally stable inverted perovskite solar cells using an electropolymerized Zn-porphyrin film as a dopant-free hole-transporting layer

Hydrophobic Fluorinated Conjugated Polymer as a Multifunctional Interlayer for High-Performance Perovskite Solar Cells

High-performance All Polymer Solar Cells Fabricated with Non-halogenated Solvent

Over 18.2% efficiency of layer-by-layer all-polymer solar cells enabled by homoleptic iridium(III) carbene complex as solid additive

Melamine-Doped Cathode Interlayer Enables High-Efficiency Organic Solar Cells