Abstract:The subject of this paper is the influence of the partial substitution of cement with mineral additive on the properties of polymer–cement composites (PCCs). Although there is considerable research on the use of perlite in cement concrete, most of the previous studies were conducted with expanded perlite or ground waste perlite, and there is a lack of results evaluating its suitability with polymer–cement composites. To fill this gap, this paper presents the mechanical characteristic of PCC mortars containing waste perlite powder. The modification consisted of replacing part of the cement with waste perlite powder, a byproduct formed during the expansion and fractionation of perlite. The granulometric characteristics of the powder were compiled, and its specific surface area and density were determined. A chemical composition analysis was also carried out. An aqueous dispersion of styrene–acrylic copolymer was used as a polymer modifier. The proportions (by mass) between the contents of the PCC composite components, i.e., cement/polymer (0 to 20%) and cement/mineral powder (0 to 15%), were used as material variables. The technical characteristics tested included the compressive, flexural, and tensile strengths at 28 and 90 days of curing. The compositions of the tested composites were determined using the statistical planning of the experiment. At a low polymer-modifier content in PCC mortars (2.93%), the tested mechanical strengths decreased by five times, with a 6-fold increase in waste content. For mortars containing more than 10% of the polymer modifier, no effect of waste material powder on the flexural strength was observed, while with relatively minor reductions in compressive strength of 2% and 5% and tensile strength of 4% and 2% were observed after 28 and 90 days of curing, respectively. It was shown that it is possible to use waste perlite powder as an ingredient in construction polymer–cement composites, while there is a limiting waste content, above which there is a deterioration in mechanical properties.

Effect of porcelain polishing waste additive on properties and corrosion resistance of ceramic foams produced from zeolite

Novel Glass Ceramic Foams Materials Based on Polishing Porcelain Waste Using the Carbon Ash Waste As Foaming Agent

Fabrication of foamed ceramics with enhanced compressive strength and low thermal conductivity via a simple route

Effects of Ammonium Molybdate Additive and Sintering Temperature on the Properties of Foam Ceramics Based on Ceramic Tile Polishing Waste

Preparation of porous ceramics with waste zeolites as raw material

Preparation of eco-friendly porous ceramic with low thermal conductivity by high-temperature treatment of foamed solid waste based geopolymer with cenospheres

Effect of Additives on the Synthesis of Foam Glasses from Polishing Porcelain Tile Waste and Carbon Ash

Synthesis of a foam ceramic based on ceramic tile polishing waste using SiC as foaming agent

Effects of olive oil on physical and mechanical properties of ceramic waste-based geopolymer foam

Foaming mechanism of polishing porcelain stoneware tile residues via adding C, Al and Si powder

Preparation of ceramic foams from ceramic tile polishing waste and fly ash without added foaming agent

Fabrication of Mullite-Corundum Foamed Ceramics for Thermal Insulation and Effect of Micro-Pore-foaming Agent on Their Properties

Design and Formulation of Polyurethane Foam Used for Porous Alumina Ceramics

Effect of holding time on the properties of porous ceramics with high-volume polished slag and its pore structure characteristics

The Effect of Mineral Wool Fiber Additive on Several Mechanical Properties and Thermal Conductivity in Geopolymer Binder

Preparation and characterization of ceramic foams mainly containing extracted titanium residues and silica tailings

Highly Porous Zirconia Ceramic Foams with Low Thermal Conductivity from Particle‐Stabilized Foams

Effects of Foaming Agent on Microstructure and Properties of Porous Mullite Ceramics

Reuse of mineral wool waste and recycled glass in ceramic foams

Synthesis of foamed glass–ceramics from high‐titanium blast furnace slag using Na3PO4·12H2O as a foam stabilizer

The Influence of Waste Perlite Powder on Selected Mechanical Properties of Polymer–Cement Composites