Abstract:Journal of Thermoplastic Composite Materials, Ahead of Print. The current research work involves the fabrication and tribological properties analysis of constant basalt filler reinforced (30 wt %) bio-based polypropylene (PP) and high density polyethylene (HDPE) thermoplastic composites. Compression molding technique is used after an internal mixing process in order to produce composite samples. The physical and hardness properties have been evaluated for both neat polymers and composite samples. In order to study the coefficient of friction (COF) and specific wear rate (SWR) of PP and HDPE composite samples, the Taguchi and Analysis of Variance (ANOVA) methodologies were applied. For PP samples, the optimum parameters in response to COF are found to be 0 wt% basalt (rank 3), 9 N load (rank 1), 200 r/min speed (rank 4), and 100 m distance (rank 2); for the SWR output, the optimum parameters are 30 wt% basalt (rank 1), 6 N load (rank 4), 100 r/min speed (rank 2), and 200 m distance (rank 3). For HDPE samples, the optimum parameters in response to COF are 0 wt% basalt (rank 1), 6 N load (rank 3), 100 r/min speed (rank 4), and 100 m distance (rank 2); for the SWR output, the optimum parameters are 30 wt% basalt (rank 1), 6 N load (rank 3), 100 r/min speed (rank 4), and 150 m distance (rank 2). Consistently, it has been shown that incorporating basalt fillers to PP and HDPE composites has more dramatically decreased SWR than COF. The depth of wear constantly rises according to increasing load, irrespective of the processing variables, as shown in 2D depth profiles. It is discovered that the confirmation tests carried out for the optimum parameters are within statistically acceptable bounds. The depth profile plots revealed that the worn track edges are found with polymer bumps because of deep grooves and softened polymer debris, which commonly observed more with HDPE samples due to low softening temperature. Moreover, the worn surfaces of the composites have plowed lines and cracks that are brought about by the micro-cutting and micro-plowing activity of the erosive asperities counterface. In addition to surface characteristics, the transfer films created during sliding also significantly influenced the mode of sample wear.

Comparative study on three body abrasive wear behaviour of natural compliant thermoplastic composite under dry and lubricated conditions

Three body abrasive wear assessment of novel jute/natural rubber flexible green composite

Wear and Frictional Performance of Epoxy Composites Reinforced with Natural Waste Fibers and Fillers for Engineering Applications

A Comparative Analysis of the Tribological Performance of Coir, Bamboo and Wood Filler Reinforced Polymer Composites

Effect of tungsten carbide on mechanical and tribological properties of jute/sisal/E-glass fabrics reinforced natural rubber/epoxy composites

Friction and wear behavior of polyetherimide composites in various wear modes

Development of Sustainable Jute/Epoxy Composite and Assessing the Effect of Rubber Crumb on Low Velocity Impact Response

Friction and Wear Studies on Jute Fiber and SS 304 Wire Mesh Reinforced Hybrid Polymer Composites for Automotive Applications

Comparison of Friction and Wear Performances of Pure Poly-ether-ether-ketone Polymer and Carbon Fiber Reinforced Poly-ether-ether-ketone Polymer Composite for Bushing and Bearing Applications

Tribological performance analysis of sustainable basalt micro-filler loaded bio-based polypropylene and high density polyethylene composites

Investigation of mechanical and tribological performance of wood dust reinforced epoxy composite under dry, wet and heated contact condition

Influence of Load and Sliding Velocity on Abrasive Wear of Polyester Composites Reinforced with Bio-Particulates as Filler Material

Physical, mechanical and dry sliding wear properties of non-woven viscose fabric epoxy-based polymer composites: An optimization study

Tribo-informatics evaluation of dry sliding friction of silanized jute filler reinforced epoxy composites using machine learning techniques

Comparative Analysis of Erosive Wear Behaviour of Epoxy, Polyester and Vinyl Esters Based Thermosetting Polymer Composites for Human Prosthetic Applications Using Taguchi Design

Optimization and Prediction of Wear Characteristics of Khas Khas Grass/Mesquite Bark Powder/Banana Fiber-Reinforced Epoxy Green Hybrid Composites Using Taguchi Technique

Slurry erosive study and optimization of material and process parameters of single and hybrid matrix flexible composites using Taguchi approach

A comparative analysis of dry sliding wear characterization of textile wastes (cotton/jute fabrics) reinforced nano fly ash filled epoxy based hybrid composites

Mechanical Interlocking Approaches to the Prediction of Mechanical and Tribological Behavior of Natural Fiber-Reinforced Polymer Hybrid Nanocomposites or Automotive Applications

Experimental investigation on dry frictional behavior of the two self-lubricating composites under heavy loading conditions

Tribological performances of polymeric plain bearings made of epoxy matrix with UHMWPE, MoS2, Kevlar and base oil as the fillers