Abstract:The effects of austenitizing and austempering temperatures on the bainite transformation kinetics and the microstructural and mechanical properties of a medium-carbon high-silicon ultra-fine bainitic steel were investigated via dilatometric measurements, microstructural characterization and mechanical tests. It is demonstrated that the optimum austenitizing temperature exists for 0.3 wt.%C ultra-fine bainitic steel. Although the finer austenite grain at 950 °C provides more bainite nuclei site and form finer bainitic ferrite plates, the lower dislocation density in plates and the higher volume fraction of the retained austenite reduces the strength and impact toughness of ultra-fine steel. When the austenitizing temperature exceeds 1000 °C, the true thickness of bainitic ferrite plates and the volume fraction of blocky retained austenite in the bainite microstructure increase significantly with the increases in austenitizing temperature, which do harm to the plasticity and impact toughness. The effect of austempering temperature on the transformation behavior and microstructural morphology of ultra-fine bainite is greater than that of austenitizing temperature. The prior martensite, formed when the austempering temperature below Ms, can refine the bainitic ferrite plates and improve the strength and impact toughness. However, the presence of prior martensite divides the untransformed austenite and inhibits the growth of bainite sheaves, thus prolonging the finishing time of bainite transformation. In addition, prior martensite also strengthens the stability of untransformed austenite though carbon partition and enhances the volume fraction of blocky retained austenite, which reduces the plasticity of ultra-fine bainitic steel. According to the experimental results, the optimum austempering process for 0.3 wt. %C ultra-fine bainitic steel is through austenitization at 1000 °C and austempering at 340 °C.

Effect of pre-formed martensite quenching plus inverted multi-step heat treatment on medium-carbon alloy steel

Inverted multi-step bainitic austempering process routes: Enhanced strength and ductility

Notably improved mechanical properties via introducing a short austempering treatment on low-carbon martensite steel

Effect of prior martensite formation on the bainite transformation kinetics in high-strength 3% Mn multiphase steel

Nanostructured Martensite–austenite Dual Phase Steels

Influence of Prior Martensite on Bainite Transformation, Microstructures, and Mechanical Properties in Ultra-Fine Bainitic Steel

Effects of Isothermal Transformation at the Quenching Temperature on the Microstructure and Mechanical Properties of a Medium-Carbon Steel

Microstructure and Properties of a Low Carbon Bainitic Steel Produced by Conventional and Inverted Two-Step Austempering Processes

Introducing ultrafine ferrite in low-temperature bainitic steel through a novel process for simultaneously improving strength and toughness

Ultra-Fine Bainite in Medium-Carbon High-Silicon Bainitic Steel

Kinetics of Martensite/Austenite Decomposition during Tempering of Ultrafine Nano-Bainitic Steels

Effect of Intercritical Austenitizing Temperature during Quenching–Intercritical Quenching–Tempering Process on Toughness of 25Mn2Si2Cr Bainitic Steel

Effect of Pre-Existed Austenite on Austenite Reversion and Mechanical Behavior of an Fe-0.2C-8Mn-2Al Medium Mn Steel

Influence of Isothermal Treatment Prior to Initial Quenching of Q&P Process on Microstructure and Mechanical Properties of Medium Mn Steel

Mechanism of Mitigating Quenching Cracking for B-containing 9cr Martensitic Heat Resistant Steel by Austempering Process

Comparison of Microstructure and Mechanical Properties of a High‐Carbon Bainitic Steel Treated by Long‐Time Bainitic Austempering and Short‐Time Austempering Plus Tempering Processes

A novel microstructural design and heat treatment technique based on gradient control of carbon partitioning between austenite and martensite for high strength steels

Effect Of Two-Step Austempering Process On Transformation Kinetics Of Nanostructured Bainitic Steel

Simultaneously Improved Strength and Impact Toughness by Introducing Ultrafine Ferrite in Low-Temperature Bainitic Steel

Effect of Rapid Heating and Quenching on Microstructure and Mechanical Properties of High Strength Low Alloy Steel