Abstract:Currently, intensive research is being conducted on Ruddlesden–Popper-type two-dimensional (2D) perovskite-based solar cells because of the advantages such as excellent power conversion efficiency (PCE) and desirable environmental stability. A well-crystallized perovskite film plays a very important role in enhancing the performance of perovskite solar cells (PSCs). In this study, we investigated the effect of the wetting property of the underlying hole-transport layer (HTL) on the crystallization of 2D perovskite films. Three HTL layers with varied hydrophobicities, including hydrophilic poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS), moderate-hydrophobic poly(bis(4-phenyl)(2,4,6-trimethylphenyl)amine) (PTAA), and high-hydrophobic poly(3-hexylthiophene-2,5-diyl) (P3HT), were used to fabricate 2D PSCs, and the quality of the resulting perovskite films was examined. We found that moderate-hydrophobic PTAA resulted in a compact and uniform perovskite morphology with enhanced crystallinity. By contrast, the perovskite film formed on hydrophilic PEDOT:PSS showed a rough morphology with overlapping perovskite planes. This is because the hydrophobic PTAA surface could suppress the heterogeneous nucleation of perovskite and facilitate the boundary mobility of perovskite grains. Therefore, a high PCE value of 12.3% was achieved for the PTAA-based PSCs, which is higher than that of the PSCs using PEDOT:PSS (10.5%). However, the perovskite film formed on the highly hydrophobic P3HT showed a low surface coverage, resulting in an even lower PCE of 8.3%. This might be due to the higher hydrophobicity of P3HT, which leads to a low adhesion force with the precursor. The 2D PSCs using PTAA also show better long-term and thermal stability than the PEDOT:PSS-based case, with a suppressed PCE degradation from 26 to 17%. Our results indicate that using moderate-hydrophobic PTAA as the HTL is beneficial for fabricating efficient 2D PSCs with higher stability.The Supporting Information is available free of charge at https://pubs.acs.org/doi/10.1021/acsaem.1c01531.Contact angle of pristine PTAA (Figure S1), J–V characteristics of P3HT-based PSCs (Figure S2), UV–vis absorption spectrum of the P3HT film (Figure S3), J–V characteristics and device parameters of PTA-based PSCs (Figure S4 and Table S1), transmission spectra of PEDOT:PSS and PTAA films (Figure S5), dark J–V characteristics of the PSCs (Figure S6), and stability measurements (Figure S7) (PDF)This article has not yet been cited by other publications.

Physical Effects of 2PACz Layers as Hole-Transport Material on the Performance of Perovskite Solar Cell

Mitigating Detrimental Effect of Self‐Doping Near the Anode in Highly Efficient Organic Solar Cells

Comprehensively Evaluating Feasibility of Self-assembled Materials Applied to Hole Transport Layer for Commercializing Perovskite Solar Cells

Synergistic Effects of the Physical Modification and Chemical Passivation Enabling Efficient Perovskite Solar Cells

Simultaneously Enhancing the Efficiency and Stability of Perovskite Solar Cells by Using P3HT/PEDOT:PSS as a Double Hole Transport Layer

A Dual-Functional Conjugated Polymer as an Efficient Hole-Transporting Layer for High-Performance Inverted Perovskite Solar Cells

PEDOT:PSS/CuCl Composite Hole Transporting Layer for Enhancing the Performance of 2D Ruddlesden-Popper Perovskite Solar Cells

Tailored PEDOT:PSS hole transport layer for higher performance in perovskite solar cells: Enhancement of electrical and optical properties with improved morphology

Tuning interfacial chemical interaction for high-performance perovskite solar cell with PEDOT:PSS as hole transporting layer

Conjugated Phosphonic Acids Enable Robust Hole Transport Layers for Efficient and Intrinsically Stable Perovskite Solar Cells

Hole-Transport-Underlayer-Induced Crystallization Management of Two-Dimensional Perovskites for High-Performance Inverted Solar Cells

Surface Modification of PEDOT:PSS for Enhanced Performance of Inverted Perovskite Solar Cells

Boosting Performance of Inverted Perovskite Solar Cells by Diluting Hole Transport Layer

Understanding the Mechanism of PEDOT: PSS Modification Via Solvent on the Morphology of Perovskite Films for Efficient Solar Cells

Water-resistant PEDOT:PSS hole transport layers by incorporating a photo-crosslinking agent for high-performance perovskite and polymer solar cells

Resolving the Hydrophobicity of Me-4PACz Hole Transport Layer for High-Efficiency Inverted Perovskite Solar Cells

Pathway to the Polyvinyl‐Acetate‐Assisted PEDOT:PSS as a Dopant‐Free Hole Transporting Material in Planar Heterojunction Perovskite Solar Cells

Interface Engineering of Perovskite/Hole Transport Layer Using Nano‐Network Formation in Small Molecule–Polymer Blend for Efficient Inverted Perovskite Solar Cells

Ti3C2Tx-Modified PEDOT:PSS Hole-Transport Layer for Inverted Perovskite Solar Cells

2,3-Diphenylthieno[3,4- b ]pyrazines as Hole-Transporting Materials for Stable, High-Performance Perovskite Solar Cells

Hydrophobic poly-TPD modified PEDOT PSS surface for improved and stable photovoltaic performance of MAPbI3 based p-i-n perovskite solar cells