Resolving the Hydrophobicity of Me-4PACz Hole Transport Layer for High-Efficiency Inverted Perovskite Solar Cells

Kashimul Hossain,Ashish Kulkarni,Urvashi Bothra,Benjamin Klingebiel,Thomas Kirchartz,Michael Saliba,Dinesh Kabra

2023-04-27

Abstract:[4-(3,6-dimethyl-9H-carbazole-9-yl)butyl]phosphonic acid (Me-4PACz) self-assembled monolayer (SAM) has been employed in perovskite single junction and tandem devices demonstrating high efficiencies. However, a uniform perovskite layer does not form due to the hydrophobicity of Me-4PACz. Here, we tackle this challenge by adding a conjugated polyelectrolyte poly(9,9-bis(3'-(N,N-dimethyl)-N-ethylammonium-propyl-2,7-fluorene)-alt-2,7-(9,9dioctylfluorene)dibromide (PFN-Br) to the Me-4PACz in a specific ratio, defines as Pz:PFN. With this mixing engineering strategy of Pz:PFN, the PFN-Br interacts with the A-site cation and is confirmed via solution-state nuclear magnetic resonance studies. The narrow full width at half maximum (FWHM) of diffraction peaks of perovskite film revealed improved crystallization on the optimal mixing ratio of Pz:PFN. Interestingly, the mixing of PFN-Br additionally tunes the work function of the Me-4PACz as revealed by the Kelvin probe force microscopy and built-in-voltage estimation in solar cells. Devices employing optimized Pz:PFN mixing ratio deliver open-circuit voltage (Voc)of 1.16 V and efficiency >20% for perovskites with a bandgap of 1.6 eV with high reproducibility and concomitant stability. Considering significant research on Me-4PACz SAM, our work highlights the importance of obtaining a uniform perovskite layer with improved yield and performance.

Materials Science

What problem does this paper attempt to address?

This paper aims to address the issue encountered when using the Me-4PACz hole transport layer in perovskite solar cells (PSCs), specifically the inability to form a uniform perovskite layer due to the hydrophobicity of Me-4PACz. The authors tackled this challenge by employing a mixed engineering strategy that combines the conjugated polyelectrolyte PFN-Br with Me-4PACz. Specifically, PFN-Br interacts with the A-site cations of the perovskite, which was confirmed through solution-state nuclear magnetic resonance studies. The perovskite films with the optimal mixing ratio exhibited a narrower full width at half maximum (FWHM), indicating improved crystallinity. Additionally, the addition of PFN-Br modulated the work function of Me-4PACz, enhancing energy level alignment. Experimental results showed that devices using the optimized mixing ratio achieved efficiencies exceeding 20% along with good reproducibility and stability. This work underscores the importance of obtaining uniform and performance-enhanced perovskite layers.

Resolving the Hydrophobicity of Me-4PACz Hole Transport Layer for High-Efficiency Inverted Perovskite Solar Cells

Resolving the Hydrophobicity of the Me-4PACz Hole Transport Layer for Inverted Perovskite Solar Cells with Efficiency >20%

Reconstruction of Hole Transport Layer via Co‐Self‐Assembled Molecules for High‐Performance Inverted Perovskite Solar Cells

Vacuum‐assisted deposition of highly hydrophobic self‐assembled monolayer for high‐efficiency perovskite solar cells

Stereo‐Hindrance Induced Conformal Self‐Assembled Monolayer for High Efficiency Inverted Perovskite Solar Cells

Mixed self‐assembled hole‐transport monolayer enables simultaneous improvement of efficiency and stability of perovskite solar cells

Comprehensively Evaluating Feasibility of Self-assembled Materials Applied to Hole Transport Layer for Commercializing Perovskite Solar Cells

Compact Hole‐selective Self‐assembled Monolayers Enabled by Disassembling Micelles in Solution for Efficient Perovskite Solar Cells

A Universal Strategy of Perovskite Ink ‐ Substrate Interaction to Overcome the Poor Wettability of a Self‐Assembled Monolayer for Reproducible Perovskite Solar Cells

Synchronous Modulation of Hole-Selective Self-Assembled Monolayer and Buried Interface for Inverted Perovskite Solar Cells

4-Methoxy phenethylammonium halide salts for surface passivation of perovskite films towards efficient and stable solar cells

Repairing Interfacial Defects in Self-Assembled Monolayers for High-Efficiency Perovskite Solar Cells and Organic Photovoltaics through the SAM@Pseudo-Planar Monolayer Strategy

Modification of Hydrophobic Self‐Assembled Monolayers with Nanoparticles for Improved Wettability and Enhanced Carrier Lifetimes Over Large Areas in Perovskite Solar Cells

Enhanced efficiency and stability of PM6:Y6 organic solar cells using hydrophobic self-assembled monolayers

Synergistic Interface Layer Optimization and Surface Passivation with Fluorocarbon Molecules toward Efficient and Stable Inverted Planar Perovskite Solar Cells

Conjugated linker-boosted self-assembled monolayer molecule for inverted perovskite solar cells

Hydrophobic Fluorinated Conjugated Polymer as a Multifunctional Interlayer for High-Performance Perovskite Solar Cells

Facile post‐treatment of self‐assembled monolayers for efficient inverted perovskite solar cells

Enhancing Surface Modification and Carrier Extraction in Inverted Perovskite Solar Cells via Self-Assembled Monolayers

Engineering of Electron Extraction and Defect Passivation Via Anion-Doped Conductive Fullerene Derivatives As Interlayers for Efficient Invert Perovskite Solar Cells.

Improved Hole‐Selective Contact Enables Highly Efficient and Stable FAPbBr3 Perovskite Solar Cells and Semitransparent Modules