Abstract:Charge accumulation and charged defects at both bulk and buried heterojunction interfaces of perovskites are primarily related to the photovoltaic performance and shelf stability of perovskite solar cells (PSCs). Moreover, detrimental defects distributing along the perovskite bottom side in contact with the tin oxide (SnO2) surface may exert unparalleled significance in charge extraction and transport. Most importantly, interfacial nonradiative recombination can also widely exist, which will seriously hamper efficiency of the related device. In this work, a multifunctional chemical bridge at the perovskite/SnO2 interface is devised through triggering an in situ polymerization strategy, by which cross-linked polymerizable 3-(trimethoxysilyl)propyl methacrylate (MAPS) monomers under the combination of temperature and initiators can form bulkier macropolymers (MAPS dimers). Detailed theoretical and experimental results reveal that the carbonyl groups (CO) of both MAPS monomers and MAPS dimers can chemically anchor to perovskite bottom side through a CO···Pb coordination bond interaction to regulate the film quality and the siloxane groups effectively couple with oxygen vacancies on the SnO2 film surface to facilitate its optoelectronic properties. Compared with the primitive MAPS monomer units, the resultant MAPS dimers simultaneously prevent interfacial charge accumulation and demonstrate a more benign energy level alignment to further augment photovoltaic performance of PSCs. Thus, the devices assembled under open-air conditions based on double-sided passivation deliver a decent photoelectronic performance with the champion efficiency of 20.94% accompanied by negligible hysteresis. Meanwhile, the unencapsulated targeted devices maintain 93.1% and 86.5% of their original efficiency after continuous 500 h thermal treatment and 500 h light illumination under open-circuit conditions, respectively.

Synchronous Modulation of Hole-Selective Self-Assembled Monolayer and Buried Interface for Inverted Perovskite Solar Cells

Reconstruction of Hole Transport Layer via Co‐Self‐Assembled Molecules for High‐Performance Inverted Perovskite Solar Cells

Versatile Energy-Level-Tunable Hole-Transport Layer for Multi-Composition Inverted Perovskite Solar Cells

Rational molecular design of multifunctional self-assembled monolayers for efficient hole selection and buried interface passivation in inverted perovskite solar cells

Dimethyl Acridine-Based Self-Assembled Monolayer As a Hole Transport Layer for Highly Efficient Inverted Perovskite Solar Cells

Conjugated Self-Assembled Monolayer as Stable Hole-Selective Contact for Inverted Perovskite Solar Cells

Multifunctional Action Site Strategy of a Buried Interface for High-Performance Perovskite Solar Cells

Stereo‐Hindrance Induced Conformal Self‐Assembled Monolayer for High Efficiency Inverted Perovskite Solar Cells

Self-Doping a Hole-Transporting Layer Based on a Conjugated Polyelectrolyte Enables Efficient and Stable Inverted Perovskite Solar Cells

Dynamic Self-Assembly of Small Molecules Enables the Spontaneous Fabrication of Hole Conductors at Perovskite/electrode Interfaces for over 22% Stable Inverted Perovskite Solar Cells.

Deciphering the Reduced Loss in High Fill Factor Inverted Perovskite Solar Cells with Methoxy-Substituted Poly(Triarylamine) as the Hole Selective Contact

Enhancing Surface Modification and Carrier Extraction in Inverted Perovskite Solar Cells via Self-Assembled Monolayers

Synchronous Modulation of Defects and Buried Interfaces for Highly Efficient Inverted Perovskite Solar Cells

Simultaneous Interface Amelioration and Energy Level Modulation Using In Situ Polymerized Molecules for Efficient and Stable Perovskite Solar Cells

Repairing Interfacial Defects in Self-Assembled Monolayers for High-Efficiency Perovskite Solar Cells and Organic Photovoltaics through the SAM@Pseudo-Planar Monolayer Strategy

Dynamic Self-assembly of Small Molecules Enables Spontaneous Fabrication of Hole Conductor at Perovskite/electrode Interfaces for over 22% Stable Inverted Perovskite Solar Cells

2D/3D heterojunction engineering at the buried interface towards high-performance inverted methylammonium-free perovskite solar cells

Dual Optimization of Bulk and Interface Via the Synergistic Effect of Ligand Anchoring and Hole Transport Dopant Enables 23.28% Efficiency Inverted Perovskite Solar Cells

Interface Engineering of Perovskite/Hole Transport Layer Using Nano‐Network Formation in Small Molecule–Polymer Blend for Efficient Inverted Perovskite Solar Cells

Engineering the buried interface in perovskite solar cells via lattice-matched electron transport layer

Synergistic Buried Interface Regulation of Tin-Lead Perovskite Solar Cells via Co-Self-Assembled Monolayers