Abstract:The major limitation of organic-inorganic perovskite solar cell performance is the existence of numerous charged defects at the absorption layer surface, which caused the charge carrier to recombine depravation. These defects have a remarkable influence on charge extraction, which further caused the instability of the device and induced severe hysteresis. Here, three low-cost anion-doped conductive fullerene derivatives, fullerene bis(phenethyl alcohol) malonate (FMPE-I), fullerene bis(ethylenediamine) malonamide (FEDA-I), and fullerene bis(propanediamine) malonamide (FPDA-I), are developed for the first time as interfacial layers between perovskite and phenyl-C-61 -butyric acid methyl ester (PCBM) in planar invert perovskite solar cells by mild solution fabrication. The constituent Lewis basic halides and the specific amide groups of conductive fullerene derivatives efficaciously heighten the chemical interaction between perovskite and conductive fullerene derivatives since the iodide can combine with undercoordinated Pb2+ by electrostatic interaction and the amide group can facilely be combined with I by hydrogen bonding, improving the dual passivation of perovskite defects. Moreover, due to the well-matched energy level of conductive fullerene derivatives and the high conductivity of the perovskite/interlayer film, the electron extraction capacity can be effectively enhanced. Consequently, superior optoelectronic properties are achieved with an improved power conversion efficiency of 17.63%, which is considerably higher than that of the bare PCBM-based devices (14.96%), for the perovskite device with conductive interlayer treatment along with negligible hysteresis. Moreover, hydrophobic conductive fullerene derivatives improve the resistance of the device to moisture. The conductive fullerene derivative-based devices without encapsulation are maintained at 85% of the pristine power conversion efficiency value after storage under ambient conditions (25 degrees C temperature, 60% humidity) for 500 h.

Resolving the Hydrophobicity of the Me-4PACz Hole Transport Layer for Inverted Perovskite Solar Cells with Efficiency >20%

Resolving the Hydrophobicity of Me-4PACz Hole Transport Layer for High-Efficiency Inverted Perovskite Solar Cells

Stereo‐Hindrance Induced Conformal Self‐Assembled Monolayer for High Efficiency Inverted Perovskite Solar Cells

Reconstruction of Hole Transport Layer via Co‐Self‐Assembled Molecules for High‐Performance Inverted Perovskite Solar Cells

Vacuum‐assisted deposition of highly hydrophobic self‐assembled monolayer for high‐efficiency perovskite solar cells

Mixed self‐assembled hole‐transport monolayer enables simultaneous improvement of efficiency and stability of perovskite solar cells

Synchronous Modulation of Hole-Selective Self-Assembled Monolayer and Buried Interface for Inverted Perovskite Solar Cells

A Universal Strategy of Perovskite Ink ‐ Substrate Interaction to Overcome the Poor Wettability of a Self‐Assembled Monolayer for Reproducible Perovskite Solar Cells

Enhancing Hole Transport Uniformity for Efficient Inverted Perovskite Solar Cells Through Optimizing Buried Interface Contacts and Suppressing Interface Recombination.

Comprehensively Evaluating Feasibility of Self-assembled Materials Applied to Hole Transport Layer for Commercializing Perovskite Solar Cells

Conjugated linker-boosted self-assembled monolayer molecule for inverted perovskite solar cells

Compact Hole‐selective Self‐assembled Monolayers Enabled by Disassembling Micelles in Solution for Efficient Perovskite Solar Cells

Repairing Interfacial Defects in Self-Assembled Monolayers for High-Efficiency Perovskite Solar Cells and Organic Photovoltaics through the SAM@Pseudo-Planar Monolayer Strategy

Synergistic Interface Layer Optimization and Surface Passivation with Fluorocarbon Molecules toward Efficient and Stable Inverted Planar Perovskite Solar Cells

4-Methoxy phenethylammonium halide salts for surface passivation of perovskite films towards efficient and stable solar cells

Modification of Hydrophobic Self‐Assembled Monolayers with Nanoparticles for Improved Wettability and Enhanced Carrier Lifetimes Over Large Areas in Perovskite Solar Cells

Improved Hole‐Selective Contact Enables Highly Efficient and Stable FAPbBr3 Perovskite Solar Cells and Semitransparent Modules

In Situ Dehydration Condensation of Self‐Assembled Molecules Enables Stabilization of CsPbI3 Perovskites for Efficient Photovoltaics

Engineering of Electron Extraction and Defect Passivation Via Anion-Doped Conductive Fullerene Derivatives As Interlayers for Efficient Invert Perovskite Solar Cells.

Interfacial band bending and suppressing deep level defects via Eu-MOF-mediated cathode buffer layer in an MA-free inverted perovskite solar cell with high fill factor

Hydrophobic Fluorinated Conjugated Polymer as a Multifunctional Interlayer for High-Performance Perovskite Solar Cells