Abstract:Previous research often failed to prepared polymer-derived SiOC ceramic components with dense and thick monoliths/skeletons based on additive manufacturing processes, due to the porosities and cracks generated during the pyrolysis process. Herein, we report a simple solution which combines the introduction of phenolic resin (PR) as an additive and the use of controlled strategy of pyrolysis, for the vat photopolymerization additively manufactured SiOC ceramics. As a result, crack-free dense monolith and lattice skeleton structural polymer-derived SiOC ceramics are successfully prepared despite the low ceramic yield of 19.3 wt% and large linear shrinkage of 50% generated after pyrolysis. The prepared dense monoliths possess a thickness of over 5 mm and the lattices show attainable maximum dense skeletons thickness of ~2 mm. The maximum dense thickness of the samples after pyrolysis is over 7 times that of other samples prepared based on additive manufacturing reported in the literature. As an indicator of dimensional retention, the specific dense thickness to ceramic yield ratio (T/Y) is deduced, resulting maximum values of 101.9 μm/(wt%) for lattice skeletons and 254.7 μm/(wt%) for monoliths. The former is even larger than that for dense monolith SiOC structures prepared by other conventional gel casting and isostatic pressing techniques with much higher ceramic yields of > 80 wt%, and is about 6.1 times the largest T/Y ratio (=16.7 μm/(wt%)) achievable in the AM-based works reported in the literature. This shows predominance of the current work over other types of polymer-derived ceramic structures prepared by additive manufacturing and even conventional methods. The lattice structures’ apparent density and specific strength reached 0.55 g/cm3 and 6.6 × 104 N∙m/kg, respectively. The mechanical performance surpasses other structural polymer-derived ceramic structures with similar apparent density reported in the literature. Through the advanced characterization and analysis of material phase and morphology evolution during the pyrolysis process, the mechanism of defect-free densification is revealed. That is, the introduction of PR enables a highly smooth gas-releasing process due to the generation of ordered gas-releasing channels in the sample bodies during the pyrolysis process. As a result, the generation of cracks and defects was successfully prevented. Moreover, due to the high carbon residue of the PR, the samples containing 15 wt% PR in the preceramic state still possessed amorphous SiOC ceramics after pyrolysis at 1400 °C, while 0 wt% PR samples showed SiC crystallization. Compared with similar materials reported, the ceramics prepared in this study exhibit enhanced structural and mechanical performance. The strategy investigated in the study can be a viable route for the additive manufacturing of high-performance crack-free and thick monolith and lattice skeleton SiOC ceramic structures based on vat photopolymerization.

Repair of surface cracks in 3D-printed porous ceramic skeletons after sintering

3D-Printed Bioceramic Scaffolds with High Strength and High Precision

POLYMER-DERIVED SIC CERAMIC WITH TRIPLY PERIOD MINIMAL SURFACE STRUCTURE FABRICATION THROUGH DIGITAL LIGHT PROCESSING

Structure design influencing the mechanical performance of 3D printing porous ceramics

A strategy for defects healing in 3D printed ceramic compact via cold isostatic pressing: Sintering kinetic window and microstructure evolution

Ultrahigh Strength of Three-Dimensional Printed Diluted Magnesium Doping Wollastonite Porous Scaffolds

Microstructures, Mechanical Properties and Electromagnetic Wave Absorption Performance of Porous SiC Ceramics by Direct Foaming Combined with Direct-Ink-Writing-Based 3D Printing

Preparation and Characterization of 3D Printed Porous 45S5 Bioglass Bioceramic for Bone Tissue Engineering Application

Application of 3D Printing Technology and Porous Nano-Ceramic Decorative Sheet in Interior Landscape Design

3D Printing of Hollow Microspheres into Strong Hierarchical Porous Ceramics

3D printing of crack-free dense polymer-derived ceramic monoliths and lattice skeletons with improved thickness and mechanical performance

Mechanical and dielectric properties of porous and wave-transparent Si3N4-Si3N4 composite ceramics fabricated by 3D printing combined with chemical vapor infiltration

Biomimetic 3D Printing of Composite Structures with Decreased Cracking

Investigation of the influence of process parameters on dimensional accuracy and post-sintering crack formation in ceramic 3D printing for porcelain-based commercial resins

A review of 3D printed porous ceramics

Microstructure and Properties of Porous Si3n4 Ceramics with A Dense Surface

Computational models for the simulation of the elastic and fracture properties of highly porous 3D-printed hydroxyapatite scaffolds

Impact of Sintering Aid Type and Content on the Mechanical Properties of Digital Light Processing 3D-Printed Si3N4 Ceramics

Bone regeneration in 3D printing bioactive ceramic scaffolds with improved tissue/material interface pore architecture in thin-wall bone defect

Microstructure and properties of porous Si 3 N 4 ceramics fabricated by digital light processing combined with spark plasma sintering

3D printing of porous SiC ceramics added with SiO2 hollow microspheres