Abstract:Shifting toward sustainability and low carbon emission necessitates recycling. Aluminum alloys can be recycled from postconsumer scrap with approximately 5% of the energy needed to produce the same amount of primary alloys. However, the presence of certain alloying elements, such as copper and zinc, as impurities in recycled Al-Mg-Si alloys is difficult to avoid. This work has investigated the influence of tiny concentrations of Cu (0.05 wt %) and Zn (0.06 wt %), individually and in combination, on the precipitate crystal structures in Al-Mg-Si alloys in peak aged and overaged conditions. To assess whether such concentrations can affect the hardening precipitate structures, atomic resolution high-angle annular dark-field scanning transmission electron microscopy and atom probe tomography were adopted. The results indicate that low levels of Cu or Zn have a significant influence. Both elements showed a relatively high tendency to incorporate into precipitate structures, where Cu occupies specific atomic sites, creating its own local atomic configurations. However, Zn exhibited distinct behavior through the formation of extended local areas with 2-fold symmetry and mirror planes, not previously observed in precipitates in Al-Mg-Si alloys. Incorporation of Cu and/or Zn will influence the precipitates' electrochemical potential relative to matrix- and precipitate-free zones and thus the corrosion resistance. Furthermore, the presence of Cu/Zn structures (e.g., β'Cu, Q'/C) enhances the thermal stability of these precipitates and, accordingly, the mechanical properties of the material. The results obtained from this work are highly relevant to the topic of recycling of aluminum alloys, where accumulation of certain alloying elements is almost unavoidable; thus, tight compositional control might be critical to avoid quality degradation.

Effect of quenching protocols on microstructure and corrosion morphology in a recycled Al–Mg–Si alloy: Tracing Cu impurities

Effect of Quenching Rate on Microstructure, Mechanical and Corrosion Properties of Al-Zn-Mg-Cu-Cr-Zr Alloy

The effect of quenching rates on microstructure and mechanical properties of an Al-Si-Cu-Mg alloy

Local corrosion mechanism of an Al-Zn-Mg-Cu alloy in oxygenated chloride solution: Cathode activity of quenching-induced η precipitates

Influence of Grain Structure on Quench Sensitivity Relative to Localized Corrosion of High Strength Aluminum Alloy

Quantified effect of quench rate on the microstructures and mechanical properties of an Al–Mg–Si alloy

Effect of grain structures and precipitation characteristics on the corrosion behaviour of Sc-containing Al-Cu-Li alloy

Enhancing Stress Corrosion Cracking Resistance of Low Cu-Containing Al-Zn-Mg-Cu Alloys by Aging Treatment Control

Effects of Rapid Quenching on Grain Boundary Microstructure and Mechanical Properties of an Al-Mg-Si-Cu Alloy

Effects of Cu Addition on the Microstructure and Properties of the Al–Mn–Fe–Si Alloy

Microstructure and Corrosion Behavior of a Zr-Sn-Nb-Fe-Cu-O Alloy Fabricated by Α+β Quenching Processing

Effect of Precipitation During Quenching on the Prediction of the Mechanical Properties of Al-5 Pct Cu Alloy after T6 Treatment

The Effect of Cu Addition on Corrosion Resistance of Al-Si-Mg-Cr Alloy

Precipitation During Quenching in 2A97 Aluminum Alloy and the Influences from Grain Structure

Effect of quenching rate on the corrosion mechanism of coarse grain and fine grain layer in 2195 aluminum-lithium alloy extruded plates

Atomic Structure of Hardening Precipitates in Al-Mg-Si Alloys: Influence of Minor Additions of Cu and Zn

In-situ electrochemical analytical effect of aging treatment on stress corrosion behavior of Al–Zn–Mg–Cu aluminum alloy

Microstructure Evolution and the Resulted Influence on Localized Corrosion in Al-Zn-Mg-Cu Alloy during Non-Isothermal Ageing

Study on the quenching sensitivity of corrosion properties in 7199 aluminum alloy

Effects of grain boundary chemistry and precipitate structure on intergranular corrosion in Al-Mg-Si alloys doped with Cu and Zn

Influence of Cu content on the hardenability of Al-xCu-1.1Li alloys