Abstract:In this study, Al-Zn-Mg-Cu alloys components were fabricated by cold metal transfer (CMT) wire arc additive manufacturing (WAAM), and the stress corrosion cracking (SCC) behavior of the alloys with different post-treatments was studied by combining in-situ electrochemical impedance spectroscopy (EIS) with slow strain rate tensile. The hot-rolling process was employed to close the internal pores of the WAAM products, following by single-stage aging (T6) to further improve the mechanical properties of the products. The elongation loss and SCC susceptibility index of T6 sample are 38.0 % and 43.0 %, respectively, which exceed those of the hot-rolled sample at 35.5 % and 37.0 %. Furthermore, the corrosion fracture of the T6 sample exhibits intensive secondary cracks, indicating an increased SCC susceptibility. The stress corrosion process is classified into four stages based on the trend of the EIS: (I) Initial stage of corrosion; (II) Corrosion products accumulation stage; (III) Corrosion products coverage stage; (IV) Approaching fracture stage. The hot-rolled samples have reduced SCC susceptibility due to the presence of coarse grain boundary precipitates (GBPs) which can act as the irreversible traps to capture hydrogen. The ultimate tensile strength and elongation of T6 sample reached 568.3 ± 11.5 MPa and 9.1 ± 0.7 %, respectively. However, the small-sized GBPs and wider precipitates-free zone reduced its SCC resistance. This study found that the hot-rolling process can fully exploit the mechanical property potential of Al-Zn-Mg-Cu alloys and improve their SCC resistance, which is an important guiding significance for the practical application of WAAM technology in Al-Zn-Mg-Cu alloys.

In-situ electrochemical analytical effect of aging treatment on stress corrosion behavior of Al–Zn–Mg–Cu aluminum alloy

Enhancing Stress Corrosion Cracking Resistance of Low Cu-Containing Al-Zn-Mg-Cu Alloys by Aging Treatment Control

Stress corrosion behavior and microstructure analysis of Al-Zn-Mg-Cu alloys friction stir welded joints under different aging conditions

Atomic-scale study on the precipitation behavior of an Al-Zn-Mg-Cu alloy during isochronal aging

Influence of aging treatments on the strength and localized corrosion resistance of aged Al–Zn–Mg–Cu alloy

Effects of Aging Treatment on Corrosion Behavior of a Tensile Deformed Al-Cu-Mn-Fe-Zr Alloy in 3.5% NaCl Solution

Effect of aging on the mechanical properties and corrosion susceptibility of an Al-Cu-Li-Zr alloy containing Sc

Microstructure Evolution and the Resulted Influence on Localized Corrosion in Al-Zn-Mg-Cu Alloy during Non-Isothermal Ageing

Revealing the mechanisms of exfoliation corrosion and stress corrosion cracking for an Al-Zn-Mg-Cu alloy after continuous retrogression and re-ageing treatment

Effect of Intermittent Variable Rate Non-isothermal Aging on the Corrosion Resistance of Al-Zn-Mg-Cu Alloy

Effects of under-aging treatment on microstructure and mechanical properties of squeeze-cast Al-Zn-Mg-Cu alloy

Effect of Overaging on Fatigue Crack Propagation and Stress Corrosion Cracking Behaviors of an Al-Zn-Mg-Cu Alloy Thick Plate

Comprehensive improvement of stress corrosion cracking resistance and strength by retrogression and re-aging in Al-8.9Zn-2.6Mg-1.7Cu alloy

Creep aging behavior and performance of Al-Zn-Mg-Cu alloys under different parameters in retrogression aging treatment

Stress corrosion behavior and microstructure analysis of Al-Zn-Mg-Cu alloys fabricated by CMT wire arc additive manufacturing with different post-treatments

Effect of continuous retrogression and re-ageing treatment on mechanical properties, corrosion behavior and microstructure of an Al-Zn-Mg-Cu alloy

Localized corrosion characteristics of Al-Mg-Si aluminum alloy with aging time and pre-delayed aging condition

Effect of aging temperature on microstructure and corrosion behavior of 6082 aluminum alloy

Correlation between stress corrosion cracking resistance and grain-boundary precipitates of a new generation high Zn-containing 7056 aluminum alloy by non-isothermal aging and re-aging heat treatment

Enhanced Fatigue Crack Propagation Resistance in an Al-Zn-Mg-Cu Alloy by Retrogression and Reaging Treatment

Effect of ECAP by Route BC and Aging Heat Treatment on the Structure and Properties of Cu0.4Cr0.3Zr Alloy