Abstract:Background: Achieving clinically adequate retention for cast crowns in prepared short abutments represents a major challenge for practicing dentists. Despite the important developments with adhesive cement, only a few teeth can be treated this way, and conventional preparation techniques are still employed for most crowns. Numerous options for auxiliary features exist; however, there is no consensus about one preferred method. This study aimed to evaluate the effect of a new innovative technique called the "double finish line technique" on full-crown retention for short abutments and to compare it with another modified preparation method. Material and methods: A comparative in vitro experimental study was conducted at the Department of Fixed Prosthodontics, Damascus University. The study sample consisted of 30 chromium-cobalt abutments and 30 metal crowns. The sample was divided into three equal groups. The first group was a control group (CG) with a 20-degree total occlusal convergence, 3 mm height, and a 0.5 mm chamfer finish line. The second group had a reduced total occlusal convergence (TOC) in the cervical 1.5 mm of the axial wall from 20 to 8 degrees. The third group implemented the so-called "double finish line technique," adding another 0.5 mm chamfer finish line 1 mm above the first finish line (DFL group). The metal crowns were cemented to metal dies with zinc-phosphate cement. Pull-off tests were applied until failure. Data were analyzed, and the differences between the three groups were detected using one-way ANOVA followed by Bonferroni's post-hoc tests (p<0.05). Results: The mean tensile strength values for the specimens were 115.36 (SD=14.59), 149.60 (SD=11.10), and 42.46 (SD=11.54) for the TOC, DFL, and CR groups, respectively. Conclusion: The reduced total occlusal convergence and double finish line techniques effectively increased full crown retention and resistance cemented on short abutments.

Fabricating crowns that fit both an implant and an existing removable partial denture

In-Office CAD/CAM Coronal Treatment With Lithium Disilicate Achieved in Efficient, Predicable Manner

A technique for fabricating single screw-retained implant-supported interim crowns in conjunction with implant surgery

Incorporation of the Altered Cast Technique in the Fabrication Workflow of an Implant-Assisted Removable Partial Denture (IARPD) for an Elderly Patient

Digital technology for fabrication of removable dental prosthesis with double crowns combining fiber-reinforced composite and zirconia

An implant impression technique involving abutment transition from interim prostheses to definitive restorations in the esthetic zone.

Trial fitting of a removable partial denture framework made using computer-aided design and rapid prototyping techniques

Material and abutment selection for CAD/CAM implant‐supported fixed dental prostheses in partially edentulous patients – A narrative review

Influence of Abutment Design on Stiffness, Strength, and Failure of Implant-Supported Monolithic Resin Nano Ceramic (RNC) Crowns

Chairside prefabricated fiber-reinforced resin composite fixed partial dentures

A custom CAD-CAM resilient attachment: A dental technique

Analysis of the efficacy of two kinds of loss restoration of posterior teeth using 3D printing temporary crown during the second phase of implant surgery

Screw-retained implant-supported crowns: An option of prosthetic restoration

Passively Fitting Implant-Supported Complete-Arch Interim Restoration

Maxillary implant-retained partial overdenture with Dolder bar attachment: a clinical report

Expediting the Rehabilitation of Severely Resorbed Ridges Using a Combination of CAD-CAM and Analog Techniques: A Case Report

Technique for cementing screwmentable implant crowns to prevent misalignment

Facially Driven Digital Workflow for Maxillary and Mandibular Milled Implant- Retained Overdentures Using Two Different Unsplinted Attachment Systems: Case Report

CLINICAL AND CYTOLOGICAL EVALUATION OF REMOVABLE PARTIAL DENTURE FABRICATED BY SELECTIVE LASER SINTERING ADDITIVE PROTOTYPING TECHNIQUE

Digital Duplication and 3D Printing for Implant Overdenture Fabrication

Evaluating the Effectiveness of the "Double Finish Line Technique" on Full-Crown Retention for Short Abutments: An In Vitro Study