Abstract:Statement of problem: New production methods have been developed for metal-ceramic restorations. Different production methods may show different surface roughness and fit, which may affect retention and long-term success. Purpose: The purpose of this in vitro study was to examine 3 different production methods with regard to surface roughness, marginal and internal fit, and retention of cobalt-chromium alloy single-crown copings. Material and methods: A master abutment of a premolar mandibular tooth preparation with 4-mm height and a 0.6-mm deep 120-degree chamfer finish line with a 12-degree angle of convergence was replicated in die stone and scanned. Thirty-six cobalt-chromium alloy copings were produced using 3 different production techniques. Twelve copings were produced by laser-sintering, 12 by milling, and 12 by milled wax/lost wax. The surface microstructure of 2 copings in each group was analyzed using interferometry. The remaining 10 copings in each group were used to evaluate marginal and internal fit by using an impression material replica method, and retention was evaluated by using a uniaxial tensile force pull-off test. The copings from each test group were cemented with zinc phosphate cement onto resin abutments. Statistical analyses of differences in marginal and internal fit were performed using 1-way ANOVA and the Mann-Whitney U test. Differences in surface topography were analyzed with the Kruskal-Wallis and Mann-Whitney U tests for nonparametric data. Differences in retentive values were analyzed using the Mann-Whitney U test for nonparametric data (all α=.05). Results: Differences in surface microstructure were seen. The laser-sintered copings showed increased surface roughness compared with milled and milled wax/lost wax copings. Differences in marginal and internal fit were noted. Laser-sintered showed significantly smaller spaces between coping and abutment than milled wax/lost wax copings (P=.003). At the margins, laser-sintered copings showed significantly smaller spaces than either the milled wax/lost wax group (P=.002) or the milled group (P=.002). At the chamfer, laser-sintered copings showed significantly smaller spaces than milled wax/lost wax copings (P=.005). At the center of the axial walls, laser-sintered copings showed significantly smaller spaces than those in the milled wax/lost wax (P=.004) and milled copings (P=.005). No significant differences were noted between milled and milled wax/lost wax copings (P>.05). No significant differences were detected regarding retentive forces in the pull-off tests (P>.05). Conclusions: Laser-sintered Co-Cr crown copings showed increased surface roughness and better internal and marginal fit than copings produced by milling or milled wax/lost wax technique. However, the crown pull-off tests did not reveal any significant differences.

Evaluating the Effectiveness of the "Double Finish Line Technique" on Full-Crown Retention for Short Abutments: An In Vitro Study

Influence of tooth preparation taper and cement type on recementation strength of complete metal crowns

Effect of abutment finish lines on the mechanical behavior and marginal fit of screw-retained implant crowns: An in vitro study

Impact of Auxiliary Features on Retention of Short Dental Crowns: An In-Vitro Analysis of Box and Groove Preparations

Effect of axial wall modification on the retention of cement-retained, implant-supported crowns

Comparison of the Effect of Implant Abutment Surface Modifications on the Retention of Implant-Supported Restorations

Retention of hybrid-abutment-crowns with offset implant placement: influence of Crown materials and Ti-base height

An Invitro Study to Evaluate the Retentive Properties of Metal Crowns on Various Surface Roughnesses of Abutments

Effects of cementation technique and cement thickness on the retention and amount of excess cement in implant-supported restorations

Cement selection for cement-retained crown technique with dental implants

The effect of two preparation designs on the fracture resistance and marginal adaptation of two types of ceramic crowns using CAD/CAM technology (In vitro study)

A new design of a multifunctional abutment to morse taper implant connection: Experimental mechanical analysis

Effect of production method on surface roughness, marginal and internal fit, and retention of cobalt-chromium single crowns

Effect of different geometric changes in the dental implant abutment body on the amount of residual excess cement and retention in a cemented implant-supported prosthesis

Evaluation of the Fatigue Strength of a CAD-CAM Nanoceramic Resin Crown on Titanium and Zirconia-Titanium Abutments

Effect of abutment design on fracture resistance of resin-matrix ceramic crowns for dental implant restoration: an in vitro study

Evaluation of periodontal parameters on abutment teeth rehabilitated with single-unit crowns: A 12-month follow-up

Influence of CAD/CAM Abutment Heights on the Biomechanical Behavior of Zirconia Single Crowns

The effect of preparation design on the fracture resistance and adaptation of the CEREC ceramic endocrowns

Effect of implant connection and restoration design (screwed vs. cemented) in reliability and failure modes of anterior crowns

Comparative in Vitro Study of Cementing Techniques for Implant-Supported Restorations.