Abstract:Binary TiAl (Ti29.8Al and Ti33.3Al, weight percent, hereafter in wt.%) alloys with different SiC fibers contents were prepared by arc melting. Microstructure, phase transformation, mechanical properties and related mechanism were elaborately researched. For the microstructure of Ti29.8Al alloy, the matrix consisted of fully alpha(2)/gamma lamellar colonies, the grain morphology changed from columnar to equiaxed when the SiC content reached 0.9%. For Ti33.3Al alloy, the matrix consisted of alpha(2)/gamma lamellar colonies and gamma phases, the columnar grains changed to equiaxed grains when the SiC content was more than 0.3%, and the grain size decreased from 150.9 to 69.3 pm with increasing SiC content. Ti5Si3 phases formed at the grain boundaries of both SiC-containing binary alloys. Ti2AlC particles would appear in the lamellar colonies when the SiC content was more than 0.9% in Ti29.8Al alloy and 0.3% in Ti33.3A1 alloy, respectively. The formation of Ti5Si3 and Ti2AlC phases resulted from the reaction of SiC fibers and TiAl alloy. The solid solution of C element in alpha(2) phase is higher than that in gamma phase, Ti2AlC will be more easily formed in Ti33.3Al alloy due to less alpha(2) phases and more gamma phases comparing with Ti29.8Al alloy. Compressive testing results showed that the strength and the strain of SiC-containing Ti29.8Al alloy were almost unchanged until the SiC content was 0.9%, which were improved to 1383 MPa and 6.5%, respectively. A good combination of strength and ductility of SiC-containing Ti33.3Al alloy was obtained, the highest values of them were 2196 MPa and 27.5% when the SiC content was 0.5%. Improvement of mechanical properties is caused by the grain refinement, grain boundary strengthening of Ti5Si3 particles, load transfer strengthening of Ti2AlC particles and solid solution strengthening of C and Si atoms.

Structural characterization and reaction mechanism of the Ti/SiC gradient material with Mg 2 Si additive fabricated by reaction sintering

Mechanical Properties and Formation Mechanism of Ti/SiC System Gradient Materials Fabricated by In-Situ Reaction Laser Cladding

The role of Mg2Si additive in sintering silicon carbide

Reaction Mechanism of Ti<SUB>3</SUB>SiC<SUB>2</SUB> Formed on the Diamond

Reaction mechanism of Ti3SiC2 formed on the diamond

Microstructure characterization and mechanical properties of in situ synthesized Ti2(Al,Si)C reinforced Al composites

Microstructure Evolution and Mechanical Properties of TiAl Binary Alloys Added with SiC Fibers

Novel (ti, W)C–SiC–WSi2 Ceramics Fabricated Via in Situ Reaction Spark Plasma Sintering at 1600 °C

Structure and Properties of C/C-SiC Prepared by Reactive Melt Infiltration

SiC Ceramics Joined with an In-Situ Reaction Gradient Layer of TiC/Ti3SiC2 and Interface Stress Distribution Simulations

Formation Mechanism and Effect on the Mechanical Properties of TiSi Phase for Ti-5Al-5Mo-5Cr-3Nb-2Zr Alloyed by Silicon

Formation Mechanism of Tisi Phase and Silicide Kinds on Microstructure and Mechanical Properties for Ti-5al-5mo-5cr-3nb-2zr Alloyed by Silicon

Microstructure and Mechanical Properties of Sicp/Mg-Zn-Ca Composites Fabricated by Stir Casting

A novel porous carbon synthesized to serve in the preparation of highly dense and high-strength SiC/SiC by reactive melt infiltration

Reaction Mechanism Of Sic-Tisi2 By Melt Infiltration Method

Densification and Mechanical Properties of Si3N4/SiC Nanocomposite Using Si-Nitrided Si3N4 Powder

Mechanism and Microstructure Transformation of 3D-Si/lg5 Composites by High Temperature Diffusion Treatment

Sintering Behavior, Microstructure and Mechanical Properties of Silicon Carbide Ceramics Containing Different Nano-Tin Additive

STUDY OF FABRICATION AND COMPRESSIVE PERFORMANCE OF ALUMINIUM ALLOY MATRIX GRADIENT COMPOSITES REINFORCED WITH SiC PARTICLES

Microstructures and mechanical properties of in-situ SiC-TiB2 ceramic composites fabricated by reactive melt infiltration

Design, Fabrication and Properties of Layered SiC/TiC Ceramic with Graded Thermal Residual Stress