Abstract:Well established understanding of flow boiling heat transfer and its hydrodynamic driving mechanisms have led to the inception of surface geometry augmentation techniques that can enhance thermal-hydraulic performance. Enhancing the flow boiling heat transfer at a reasonable pressure drop enables the deployment of more compact and efficient heat exchangers and thermal systems. To enable ease of manufacturing, simplicity, and reliability, passive augmentation techniques that do not require external stimuli are preferred. In this study, a scalable copper microstructuring technique was developed on both smooth and internally finned 0.25" tubes to investigate how it affects the thermofluidic behavior of relatively higher surface tension water during saturated flow boiling. The internally finned tubes used in this study comprised of 50 fins with a helical angle of 13°. To apply the conformal microstructures on the internal tube surfaces, chemical oxidation via an alkaline mixture was used, resulting in structures having characteristic length scales approaching 200 nm −1 μm. Our results show that microstructuring of plain copper tubes provides a water flow boiling heat transfer coefficient enhancement ranging from 10 % to 90 % compared to untreated specimens for vapor qualities ranging from 0 to 0.1 and mass flow rates ranging from 255 to 485 kg/(m 2 ·s). Augmentation is attributed to the increased roughness of the plain copper tubes that creates additional nucleation sites for enhanced liquid entrapment and increases wettability. Associated with this heat transfer augmentation is an increased pressure drop ranging from 0.5 % to 38 % relative to untreated tubes due to the increased skin friction as well as add fluid flow disruption. Overall, the performance factor ranged between 0.86 to 1.81 demonstrating that the augmentation in heat transfer overshadowed the increase in pressure drop. Interestingly, applying the conformal microstructures on internally finned copper tubes decreased the heat transfer coefficient and pressure drop by as much as 75 % and 45 %, respectively, when compared to the un-structured finned copper tubes counterparts. The decrease in heat transfer performance and pressure drop was attributed to partial wetting of the fin roots due to the presence of a vapor layer near the inner tube walls. Our work develops a mechanistic understanding of the role that microstructures play during flow boiling of water on industrially applicable smooth and finned tube geometries and designs.

Enhanced refrigerant flow boiling heat transfer in microstructured finned surfaces

Experimental Study of Condensation Heat Transfer of R134a Inside the Micro-Fin Tubes at High Mass Flux

Saturated water flow boiling heat transfer and pressure drop in scalably microstructured plain and finned copper tubes

Experimental investigation of flow boiling characteristics in microchannel with triangular cavities and rectangular fins

Flow Boiling Heat Transfer Characteristics in Horizontal, Three-Dimensional Enhanced Tubes

Experimental study on flow boiling characteristics of R134a inside high-heat-flux microchannels

A Comprehensive Assessment of Two-Phase Flow Boiling Heat Transfer in Micro-Fin Tubes Using Pure and Blended Eco-Friendly Refrigerants

Experimental investigation of heat transfer coefficient and frictional pressure drop in flow boiling of R513A: Comparative analysis of micro-fin and smooth tubes

Comparison of flow boiling heat transfer characteristics inside different enhanced heat transfer tubes

Numerical Investigation on Flow Boiling Heat Transfer in Elliptic Microchannel Heat Exchanger with Micro Fins

Experimental Study of Boiling Heat Transfer in Smooth/micro-Fin Tubes of Four Refrigerants

Micro-pin-finned Surfaces with Fractal Treelike Hydrophilic Networks for Flow Boiling Enhancement

Flow Boiling in Inner Annulus of Horizontal Enhanced Tubes

Flow Boiling Heat Transfer Intensification Due to Inner Surface Modification in Circular Mini-Channel

In tube condensation of low global warming potential refrigerants in an axial micro-fin aluminum tube

Heat transfer characteristics of R134a flow boiling in a microfin tube under typical ORC pressures based on comparison with a smooth tube

Enhancement of Flow Boiling Heat Transfer in Microchannel Using Micro-Fin and Micro-Cavity Surfaces

HEAT TRANSFER ENHANCEMENT IN INSERTED EXTRUDED ALUMINUM FINNED TUBES

Boiling Heat Transfer Enhancement by Using Micro-pin-finned Surface for Electronics Cooling

Experimental study of flow boiling performance of open-ring pin fin microchannels

R410A and R32 condensation heat transfer and flow patterns inside horizontal micro-fin and 3-D enhanced tubes