Abstract:Well established understanding of flow boiling heat transfer and its hydrodynamic driving mechanisms have led to the inception of surface geometry augmentation techniques that can enhance thermal-hydraulic performance. Enhancing the flow boiling heat transfer at a reasonable pressure drop enables the deployment of more compact and efficient heat exchangers and thermal systems. To enable ease of manufacturing, simplicity, and reliability, passive augmentation techniques that do not require external stimuli are preferred. In this study, a scalable copper microstructuring technique was developed on both smooth and internally finned 0.25" tubes to investigate how it affects the thermofluidic behavior of relatively higher surface tension water during saturated flow boiling. The internally finned tubes used in this study comprised of 50 fins with a helical angle of 13°. To apply the conformal microstructures on the internal tube surfaces, chemical oxidation via an alkaline mixture was used, resulting in structures having characteristic length scales approaching 200 nm −1 μm. Our results show that microstructuring of plain copper tubes provides a water flow boiling heat transfer coefficient enhancement ranging from 10 % to 90 % compared to untreated specimens for vapor qualities ranging from 0 to 0.1 and mass flow rates ranging from 255 to 485 kg/(m 2 ·s). Augmentation is attributed to the increased roughness of the plain copper tubes that creates additional nucleation sites for enhanced liquid entrapment and increases wettability. Associated with this heat transfer augmentation is an increased pressure drop ranging from 0.5 % to 38 % relative to untreated tubes due to the increased skin friction as well as add fluid flow disruption. Overall, the performance factor ranged between 0.86 to 1.81 demonstrating that the augmentation in heat transfer overshadowed the increase in pressure drop. Interestingly, applying the conformal microstructures on internally finned copper tubes decreased the heat transfer coefficient and pressure drop by as much as 75 % and 45 %, respectively, when compared to the un-structured finned copper tubes counterparts. The decrease in heat transfer performance and pressure drop was attributed to partial wetting of the fin roots due to the presence of a vapor layer near the inner tube walls. Our work develops a mechanistic understanding of the role that microstructures play during flow boiling of water on industrially applicable smooth and finned tube geometries and designs.

Experimental investigation of heat transfer coefficient and frictional pressure drop in flow boiling of R513A: Comparative analysis of micro-fin and smooth tubes

Comparative experimental studies of flow boiling heat transfer phenomena in smooth and enhanced tubes using R407C

Experimental Study of Boiling Heat Transfer in Smooth/micro-Fin Tubes of Four Refrigerants

Experimental Study of Condensation Heat Transfer of R134a Inside the Micro-Fin Tubes at High Mass Flux

Flow boiling heat transfer characteristics over horizontal smooth and microfin tubes: An empirical investigation utilizing R407c

Experimental study on the flow boiling heat transfer in horizontal tubes with composite structure

A Comprehensive Assessment of Two-Phase Flow Boiling Heat Transfer in Micro-Fin Tubes Using Pure and Blended Eco-Friendly Refrigerants

Flow pattern-based heat transfer analysis of microchannel flow boiling: An experimental investigation

Parametric variation studies of experimental flow boiling heat transfer phenomena using R407c inside an enhanced tube

Comprehensive study of flow boiling modeling inside helical micro-finned tubes: Empirical, non-convex optimization and deep learning predictive models

An Experimental Study on Flow Boiling Heat Transfer Outside Horizontal Enhanced Tubes

R410A flow boiling in horizontal annular channels of enhanced tubes, part I: Pressure drop

Numerical Investigation on Flow Boiling Heat Transfer in Elliptic Microchannel Heat Exchanger with Micro Fins

Flow Boiling in Inner Annulus of Horizontal Enhanced Tubes

Saturated water flow boiling heat transfer and pressure drop in scalably microstructured plain and finned copper tubes

Enhanced refrigerant flow boiling heat transfer in microstructured finned surfaces

R410A flow boiling coefficient in horizontal annular channels of enhanced tubes, Part II: Heat transfer

Numerical investigation of flow boiling characteristics of R134A in a smooth horizontal tube

EXPERIMENTAL STUDY ON HEAT FLUX EFFECT ON EVAPORATION IN TWO DIMPLE-GROOVED TUBES

Experimental Study of Local Heat Transfer Coefficient of R113 Flow Boiling in Vertical Square Tube

FLOW BOILING HEAT TRANSFER IN ENHANCED TUBES WITH COMPOSITE STRUCTURE