Abstract:The major emission sources of NOX are from automobiles, trucks, and various non-road vehicles, power plants, coal fired boilers, cement kilns, turbines, etc. Plasma reactor technology is widely used in gas conversion applications, such as NOx conversion into useful chemical by-product. Among the plasma treatment techniques, nonthermal plasma (NTP) is widely used because it does not cause any damage to the surfaces of the reacting chamber. In this proposed work, the feasibility of Dielectric Barrier Discharge (DBD) reactor-based nonthermal plasma (NTP) process is examined based on four operating parameters including NOx concentration (300-400 ppm), gas flow rate (2-6 lpm), applied plasma voltage (20-30 kVpp), and electrode gap (3-5 mm) for removing NOx gas from diesel engine exhaust. Optimization of NTP process parameters has been carried out using response surface-based Box-Behnken design (BBD) method and artificial neural network (ANN) method and compared with the performance measures such as R2, MSE (mean square error), RMSE (root mean square error), and MAPE (mean absolute percentage error). Two kinds of analysis were carried out based on (1) NOx removal efficiency and (2) energy efficiency. Based on the simulation studies carried out for Nox removal efficiency, the RSM methodology produces the performance measures, 0.98 for R2, 1.274 for MSE, 1.128 for RMSE, and 2.053 for MAPE, and for ANN analysis method, 0.99 for R2, 2.167 for MSE, 1.472 for RMSE, and 1.276 for MAPE. These results shows that ANN method is having enhanced performance measures. For the second case, based on the energy efficiency study, the R2, MSE, RMSE, and MAPE values from the RSM model are 0.97, 2.230, 1.493, and 2.903 respectively. Similarly based on ANN model, the R2, MSE, RMSE, and MAPE values are 0.99, 0.246, 0.46, and 0.615, respectively. From the performance measures, it is found that the ANN model is accurate than the RSM model in predicting the NOx removal/reduction and efficiency. These models demonstrate that they have strong agreement with the experimental results. The experimental results are indicated that optimum conditions arrived based on the RSM model resulted in a maximum NOx reduction of 60.5% and an energy efficiency of 66.24 g/J. The comparison between the two models confirmed the findings, whereas this ANN model displayed a stronger correlation to the experimental evidence.

The assessment of response surface methodology (RSM) and artificial neural network (ANN) modeling in dry flue gas desulfurization at low temperatures

Modeling based on machine learning to investigate flue gas desulfurization performance by calcium silicate absorbent in a sand bed reactor

Blast furnace slag for SO2 capture: Optimization and prediction using RSM and ANN

Prediction and Quantifying Parameter Importance in Simultaneous Anaerobic Sulfide and Nitrate Removal Process Using Artificial Neural Network

Modeling and Optimization of Wet Flue Gas Desulfurization System based on a Hybrid Modeling Method.

CFD analysis of influencing factors on SCR denitration efficiency of sintering flue gas based on response surface methodology

Analysis and estimation of cross-flow heat exchanger fouling in phosphoric acid concentration plant using response surface methodology (RSM) and artificial neural network (ANN)

Continuous SO2 absorption and desorption in regenerable flue gas desulfurization with ethylenediamine-phosphoric acid solution: A rate-based dynamic modeling

Artificial neural network and response surface methodology for modeling reverse osmosis process in wastewater treatment

Modeling Batch and Column Phosphate Removal by Hydrated Ferric Oxide-Based Nanocomposite Using Response Surface Methodology and Artificial Neural Network

Predictive capability evaluation of RSM and ANN models in adsorptive treatment of crystal violet dye simulated wastewater using activated carbon prepared from Raphia hookeri seeds

Experimental analysis and parameter optimization on the reduction of NOx from diesel engine using RSM and ANN Model

Numerical analysis of SO 2 removal characteristics in industrial flue gas desulfurization reactor by spray drying adsorption

Optimization of effecting parameters for flue gas desulfurization in a self‐priming venturi scrubber using response surface methodology

Predicting the performance of a desulfurizing bio-filter using an artificial neural network (ANN) model

Semi-dry flue gas desulphurization in spray towers: a critical review of applicable models for computational fluid dynamics analysis

Experimental Study on Removal Characteristics of SO3 by Wet Flue Gas Desulfurization Absorber

Modeling of Finned-Tube Evaporator Using Neural Network and Response Surface Methodology

Hybrid Modeling and Real-time Predictive Scheduling of Wet Flue Gas Desulfurization for Energy Saving and Life Extension

Desulfurization Characteristic of Calcium-Based Sorbent During Activation Process.

RSM and ANN Comparative Modelling with a Granulation Treatment in Mixed Waters