Abstract:In this work, the factors controlling the fresh state properties of limestone calcined clay cement (LC3) are assessed and compared to Portland and binary cements, extending the scope of previous research by combining rheological measurements with setting time determination and the evaluation of plastic shrinkage by a novel method. Yield stress and elastic modulus are considered indicators for the structural build-up/breakdown process when stress is applied to the system. On the other hand, plastic shrinkage occurs from the mixing to the setting of fresh paste and plays an important role in governing microstructural changes due to settlement and evaporation. Evaluation of the rheological properties with time was appropriate to give an overview of the influence and behavior of different added materials. The elastic modulus of all binders (clinker, LC3, clinker–limestone, and clinker–calcined clay) was increased from mixing to 60 min of curing as follows: 5.27 × 103 to 9.50 × 105 Pa, 5.94 × 103 to 9.87 × 105 Pa, 6.89 × 103 to 5.62 × 105 Pa and 7.85 × 103 to 1.27 × 106 Pa, respectively. Moreover, during the first three hours of curing, LC3 exhibited a reduction of plastic shrinkage by more than a factor of 2 compared to clinker cement. The use of calcined clay with clinker increases the elastic modulus of the system due to the flocculation effect and increased water absorption, while a dilution effect is contributed due to deflocculation and a free-water increase in the system when a high fraction of limestone is present in the binary cement. The combination of limestone and calcined clay with clinker can induce additional chemical reactions, which control the early age properties, such as plastic shrinkage. The obtained results can contribute to optimizing the fresh state properties of ternary blends of OPC, calcined clay, and limestone through a knowledge-based approach.

Calcined nanosized tubular halloysite for the preparation of limestone calcined clay cement (LC 3 )

Microstructural investigation and performance of LC3 cementitious materials

The Synergistic Effect of Calcained Coal-Series Kaolinite and Limestone on the Hydration of Portland Cement

Performance of Limestone Calcined Clay Cement (LC3) with various kaolinite contents with respect to chloride transport

A Fresh View on Limestone Calcined Clay Cement (LC3) Pastes

Use of spent fluid catalytic cracking catalyst (FCC) in Limestone Calcined Clay Cement (LC3) systems: Studies in pastes and mortars

Early Strength-Promoting Mechanism of Inorganic Salts on Limestone-Calcined Clay Cement

Influence of C–S–H seed and sodium sulfate on the hydration and strength of limestone calcined clay cement

Exploration of the Compressive Strength and Microscopic Properties of Portland Cement Taking Attapulgite and Montmorillonite Clay as an Additive

Limestone Calcined Clay as Potential Supplementary Cementitious Material—An Experimental Study

Compressive strength and environmental impact of sustainable blended cement with high-dosage Limestone and Calcined Clay (LC2)

Global insights into micro-macro mechanisms and environmental implications of limestone calcined clay cement (LC3) for sustainable construction applications

Efficient Utilization of Waste Marine Clay for Fine Aggregate to Develop Sustainable and Cost-Effective Strain-Hardening Cement-Based Composites

Utilization of Coal Gangue and Copper Tailings As Clay for Cement Clinker Calcinations

Use of low-grade kaolinite clays in the production of limestone calcined clay cement

Effect of different grade levels of calcined clays on fresh and hardened properties of ternary-blended cementitious materials for 3D printing

Study on the Influence of Thermoplastic Microcapsules on the Sulfate Resistance and Self-Healing Performance of Limestone Calcined Clay Cement Concrete

3D printing of calcined clay-limestone-based cementitious materials

Belite-ye'elimite-ferrite cements produced from London Clay

In situ synchrotron powder diffraction study of LC 3 cement activation at very early ages by C-S-H nucleation seeding

Effects of Using Cold Bonded Coarse and Fine Calcined Attapulgite Lightweight Aggregates on the Performance Properties of Microsilica and Fly Ash Blended Concretes