Abstract:Electron-beam additive manufacturing is one of the most promising methods for creating complex metal parts and structures. Additive manufacturing has already gained wide acceptance in the creation of various constructions from aluminum, copper, titanium, and their alloys as well as different classes of steels and other metallic materials. However, there are still many challenges associated with the additive manufacturing and post-production processing of intermetallic alloys. Thus, it is currently an urgent task for research. In this work, heat-resistant intermetallic alloys based on nickel, aluminum, and chromium were produced by dual-wire electron-beam additive manufacturing using commercial NiCr and Al wires. The microstructure, phase composition, and microhardness of the intermetallic billets are strongly dependent on the ratio of NiCr and Al wires, which have been fed during the additive growth of the material (NiCr:Al = 3:1 and NiCr:Al = 1:3). A metal-matrix composite material (Al3Ni-based intermetallide in Al-based matrix) was fabricated using the NiCr:Al = 1:3 ratio of the wires during the deposition. In tension, it fractures in a brittle manner before the plastic deformation starts, and it possesses a high microhardness of 6–10 GPa with a high dispersion of the value (the mean value is 8.7 GPa). This is associated with the complex phase composition of the material and the high fraction of a brittle Al3Ni intermetallic phase. In the material, obtained with the ratio NiCr:Al = 3:1, the ordered Ni3Al(Cr) and disordered Ni3Cr(Al) intermetallides are the dominating phases. Its microhardness turned out to be lower (4.1 GPa) than that in Al + Al3Ni-based composite, but intermetallic Ni3Al-based alloy demonstrates good mechanical properties in a high-temperature deformation regime (650 MPa, more than 10% elongation at 873 K). Microstructural studies, analysis of phase composition, and tensile mechanical properties of additively produced intermetallic materials show the perspective of dual-wire electron-beam additive manufacturing for producing intermetallic compounds for high-temperature applications.

Regularities of Structure Formation and Properties of Composite Materials Based on Aluminum–Manganese Bronze Produced by Electron Beam Additive Manufacturing with the Addition of Iron, Nickel, and Tungsten Powders During Printing

Formation of Defects and Inhomogeneities in the Structure of Composite Materials Based on Aluminum-Manganese Bronze with an In Situ Introduction of Nickel and Titanium Alloys or Steel During Wire-Feed Electron Beam Additive Manufacturing

Formation of Ultra Fine Grained Microstructure in Aluminum Bronzes of the Cu-Al, Cu-Al-Si, and Cu-Al-Si-Mn Systems After Electron Beam Additive Manufacturing

On the Features of Composite Coating, Based on Nickel Alloy and Aluminum–Iron Bronze, Processed by Direct Metal Deposition

Phase formation and morphological characteristics of aluminum bronze and nickel alloy composites produced by the additive manufacturing process

Regularities of Structure Formation During Friction Stir Processing of CuAl9Mn2 Copper Alloy with Addition of Tungsten Powder to the Surface Layer

Advanced mechanical properties of nickel‐aluminum bronze/steel composite structure prepared by wire‐arc additive manufacturing

Additive Manufacturing of Isotropic-Grained, High-Strength and High-Ductility Copper Alloys

High Wear Resistance and Mechanical Performance of NiAl Bronze Developed by Electron Beam Powder Bed Fusion

Microstructure, Phase Composition, and Mechanical Properties of Intermetallic Ni-Al-Cr Material Produced by Dual-Wire Electron-Beam Additive Manufacturing

Microstructure and Phase Composition of Ni–Cr–Al-Based Intermetallics Obtained by a Dual-Wire Electron Beam Additive Manufacturing

Impact of Using Tungsten, Cobalt, and Aluminum Additives on the Tribological and Mechanical Properties of Iron Composites

Microstructures and Phases in Electron Beam Additively Manufactured Ti-Al-Mo-Zr-V/CuAl9Mn2 Alloy

Formation of a bimetallic Ti–Al material by a wire-feed electron-beam additive manufacturing

Process Setup and Boundaries of Wire Electron Beam Additive Manufacturing of High-Strength Aluminum Bronze

Enhancement of Grain Refinement and Heat Resistance in TiB2-reinforced Al-Cu-Mg-Fe-Ni Matrix Composite Additive Manufactured by Electron Beam Melting

Structure and Properties of Cobalt-Based Superalloys After Electron Beam Additive Manufacturing

Analysis and Experimental Investigation of A356 Aluminium Alloy Hybrid Composites Reinforced with Gr-FE3O4-B4C Nanoparticles Synthesised by Selective Laser Melting (SLM)

Surface CuAl9Mn2/W Composites Prepared by Multipass Friction Stir Processing: Microstructures, Phases, and Mechanical and Tribological Properties

Effect of Casting and Additive Manufacturing on the Microstructure and Mechanical Property of Al-Cu Composites

Effects of Location on the Microstructure and Mechanical Properties of Cu-8Al-2Ni-2Fe-2Mn Alloy Produced Through Wire Arc Additive Manufacturing