Abstract:Electron-beam additive manufacturing is one of the most promising methods for creating complex metal parts and structures. Additive manufacturing has already gained wide acceptance in the creation of various constructions from aluminum, copper, titanium, and their alloys as well as different classes of steels and other metallic materials. However, there are still many challenges associated with the additive manufacturing and post-production processing of intermetallic alloys. Thus, it is currently an urgent task for research. In this work, heat-resistant intermetallic alloys based on nickel, aluminum, and chromium were produced by dual-wire electron-beam additive manufacturing using commercial NiCr and Al wires. The microstructure, phase composition, and microhardness of the intermetallic billets are strongly dependent on the ratio of NiCr and Al wires, which have been fed during the additive growth of the material (NiCr:Al = 3:1 and NiCr:Al = 1:3). A metal-matrix composite material (Al3Ni-based intermetallide in Al-based matrix) was fabricated using the NiCr:Al = 1:3 ratio of the wires during the deposition. In tension, it fractures in a brittle manner before the plastic deformation starts, and it possesses a high microhardness of 6–10 GPa with a high dispersion of the value (the mean value is 8.7 GPa). This is associated with the complex phase composition of the material and the high fraction of a brittle Al3Ni intermetallic phase. In the material, obtained with the ratio NiCr:Al = 3:1, the ordered Ni3Al(Cr) and disordered Ni3Cr(Al) intermetallides are the dominating phases. Its microhardness turned out to be lower (4.1 GPa) than that in Al + Al3Ni-based composite, but intermetallic Ni3Al-based alloy demonstrates good mechanical properties in a high-temperature deformation regime (650 MPa, more than 10% elongation at 873 K). Microstructural studies, analysis of phase composition, and tensile mechanical properties of additively produced intermetallic materials show the perspective of dual-wire electron-beam additive manufacturing for producing intermetallic compounds for high-temperature applications.

Phase formation and morphological characteristics of aluminum bronze and nickel alloy composites produced by the additive manufacturing process

Microstructure, Phase Composition, and Mechanical Properties of Intermetallic Ni-Al-Cr Material Produced by Dual-Wire Electron-Beam Additive Manufacturing

Advanced mechanical properties of nickel‐aluminum bronze/steel composite structure prepared by wire‐arc additive manufacturing

Phase constitution, microstructure and mechanical properties of a Ni-based superalloy specially designed for additive manufacturing

Effect of Aluminum, Iron and Chromium Alloying on the Structure and Mechanical Properties of (Ti-Ni)-(Cu-Zr) Crystalline/Amorphous Composite Materials

Regularities of Structure Formation and Properties of Composite Materials Based on Aluminum–Manganese Bronze Produced by Electron Beam Additive Manufacturing with the Addition of Iron, Nickel, and Tungsten Powders During Printing

Formation of Defects and Inhomogeneities in the Structure of Composite Materials Based on Aluminum-Manganese Bronze with an In Situ Introduction of Nickel and Titanium Alloys or Steel During Wire-Feed Electron Beam Additive Manufacturing

Microstructure and Phase Composition of Ni–Cr–Al-Based Intermetallics Obtained by a Dual-Wire Electron Beam Additive Manufacturing

Mechanical Properties and Fracture Mechanisms of Aluminum Matrix Composites Reinforced by Al-9(Co, Ni)(2) Intermetallics

Microstructures and Phases in Electron Beam Additively Manufactured Ti-Al-Mo-Zr-V/CuAl9Mn2 Alloy

The Enhancement Effect of Carbides on the Printability and Mechanical Properties of a Ni–Fe–Cr–Al–Ti Alloy Processed by Electron Beam Freeform Fabrication

Precipitation and Phase Transformation Mechanism of Additive Manufactured Ni-Co Base Superalloy

Characterization of Microsegregation and Secondary Phase Precipitation in Nickel-Based Superalloy after Wire-Feed Electron Beam Additive Manufacturing

The Influence of Post-Production Heat Treatment on the Multi-Directional Properties of Nickel-Aluminum Bronze Alloy Fabricated Using Wire-Arc Additive Manufacturing Process

Effect of AlN on the Mechanical and Electrochemical Properties of Aluminum Metal Matrix Composites

Phase Composition and Phase Transformation of Additively Manufactured Nickel Alloy 718 AM Bench Artifacts

An Al-Al interpenetrating-phase composite by 3D printing and hot extrusion

Application of finite element, phase-field, and CALPHAD-based methods to additive manufacturing of Ni-based superalloys

Preparation of multivariate multiphase composite coatings of Ni60/high aluminum bronze and its microstructure characteristics

On the Features of Composite Coating, Based on Nickel Alloy and Aluminum–Iron Bronze, Processed by Direct Metal Deposition

Graphene-strengthened Inconel 625 Alloy Fabricated by Selective Laser Melting