Abstract:Conductive polymer composites (CPCs) exhibit favorable density and corrosion resistance for application as bipolar plate (BP) in proton exchange membrane fuel cell (PEMFC). However, achieving CPCs that combine the required level of electrical conductivity and mechanical strength is a challenge that has limited their application in PEMFC BPs. This study explored the potential of achieving CPC BPs with high electrical and mechanical performance by using carbon black (CB) as a secondary filler in graphite-polymer composites. Polypropylene (PP)/epoxy blend was selected as the matrix due to its good combination of strength and toughness as well as its potential to form a co-continuous morphology, which promotes the formation of more continuous conducting networks within the composite, leading to enhanced electrical performance. The PP/epoxy/graphite/CB composites were prepared by melt mixing in a Rheomixer at 190 °C and 60 rpm for 10 min, followed by compression molding at 200 °C and 6 metric tonnes for 10 min. The electrical conductivity of the composites increased from 49.26 Scm−1 to 90.34 Scm−1 (in-plane) and from 0.37 Scm−1 to 9.34 Scm−1 (through-plane) as the total filler content increased from 50 to 85 wt%. The flexural strength initially increased from 45.57 MPa at 50 wt% to 51.84 MPa at 60 wt% total filler content. Further increase in total filler content led to a decrease in flexural strength. The nanosize CB particles, used as a minor filler, filled the voids between the graphite particles, leading to the formation of more conducting pathways and higher electrical conductivities compared to the PP/epoxy/graphite composites without CB fillers. The PP/epoxy/graphite/CB composite with 80 wt% total filler content exhibited the most promising in-plane conductivity (88.5 Scm−1), through-plane conductivity (8.52 Scm−1), and flexural strength (28.53 MPa) for BP application.

Preparation and properties of graphite/polypropylene composite material reinforced by chopped carbon fibers for proton‐exchange membrane fuel cell bipolar plates

Muti-Filler Composites Reinforced with Multiwalled Carbon Nanotubes and Chopped Carbon Fibers for the Bipolar Plate of Fuel Cells

Electrical and mechanical properties of polypropylene/epoxy blend-graphite/carbon black composite for proton exchange membrane fuel cell bipolar plate

Electrical conductivity enhancement of chopped carbon fiber‐reinforced epoxy composite bipolar plate for proton exchange membrane fuel cells

Effect of carbon fiber length and graphene on carbon-polymer composite bipolar plate for PEMFC

High performance polyvinylidene fluoride/graphite/multi-walled carbon nanotubes composite bipolar plate for PEMFC with segregated conductive networks

Preparation and Performance Study of PEK‐C‐OH/MWCNT‐COOH/Graphite Composite Bipolar Plates for PEMFCs With Improved Interface Properties

Gradient Structured Composite Bipolar Plates for Proton Exchange Membrane Fuel Cells

Structure and Properties of Carboxylated Carbon Nanotubes@Expanded Graphite/Polyethersulfone Composite Bipolar Plates for PEM

Composite Materials Based on Thermally Expanded Graphite for Fuel Cell's Bipolar Plates

Carbon/Carbon Composite Bipolar Plate for Proton Exchange Membrane Fuel Cells

Preparation and properties of high performance nanocomposite bipolar plate for fuel cell

Low filler and highly conductive composite bipolar plates with synergistic segregated structure for enhanced proton exchange membrane fuel cell performance

Bipolar plate design and fabrication using graphite reinforced composite laminate for proton exchange membrane fuel cells

Improved Performance of Composite Bipolar Plates for PEMFC Modified by Homogeneously Dispersed Multi-Walled Carbon Nanotube Networks Prepared by In Situ Chemical Deposition

Simultaneous electrical and mechanical properties improvement for composite expanded graphite bipolar plate by incorporating surface-activated carbon black paving on the carbonized melamine foam skeleton

Preparation and Properties of Chitosan/acidified Attapulgite Composite Proton Exchange Membranes for Fuel Cell Applications

Characteristics of Carbon Fiber Composite Current Collector Used in Proton Exchange Membrane Fuel Cell

Development of novel composite bipolar plates using surface‐modified conductive carbon filler materials for polymer electrolyte membrane fuel cells

A review on key factors influencing the electrical conductivity of proton exchange membrane fuel cell composite bipolar plates