Abstract:Carbon/polymer binder composite bipolar plates for proton exchange membrane fuel cells have attracted attention for their corrosion resistivity and ease of manufacturing. However, the hot-pressing fabrication process often leads to a resin-rich surface on the plate, which may increase the interfacial contact resistance. A number of studies have been reported to reduce resin accumulation on the surface. However, most reported methods have focused on how to exceed the United States Department of Energy conductivity and mechanical targets. Their fabrication methods are often complicated, which is hard to form flow channels directly in manufacturing. Herein, we propose a simple layer-by-layer method to prepare graphite/resin composite bipolar plates. During compression of the multilayer graphite/resin powder, elevated temperature and pressure make the resin in the inner polymer-rich layer flow toward the outer resin-deficient layers. Scanning electron microscopy with energy-dispersive X-ray analysis shows an unbroken “smiling” curve of carbon content along the whole cross-section, suggesting a continuous distribution of the resin across the whole composite. The resulting composite demonstrates a better interfacial contact resistance (9.2 mΩ cm2@100 psi) and a flexural strength (44.3 MPa) than the plates prepared by a single-layer method. Flow channels with a good molding accuracy (±4 μm) are also observed. Single-cell testing with the gradient-structured composite plate shows excellent cell performance: the cell voltage is 0.67 V at 1 A cm–2, and the maximum power density reaches 0.99 W cm–2. In situ electrochemical impedance analysis demonstrates that compared to an analogue using the single-layer loading method, the cell with gradient structured plates displays lower ohmic and mass transfer resistance than the cell using the plates prepared by a single-layer method.

Simultaneous electrical and mechanical properties improvement for composite expanded graphite bipolar plate by incorporating surface-activated carbon black paving on the carbonized melamine foam skeleton

Expanded graphite (EG)/Ni@Melamine foam (MF)/EG sandwich-structured flexible bipolar plate with excellent electrical conductivity, mechanical properties, and gas permeability

Improved Performance of Composite Bipolar Plates for PEMFC Modified by Homogeneously Dispersed Multi-Walled Carbon Nanotube Networks Prepared by In Situ Chemical Deposition

Preparation and properties of high performance nanocomposite bipolar plate for fuel cell

Carbon Black Doped Graphite Composite Bipolar Plate Compounds for Improving Conductivity

Bipolar plate design and fabrication using graphite reinforced composite laminate for proton exchange membrane fuel cells

Low filler and highly conductive composite bipolar plates with synergistic segregated structure for enhanced proton exchange membrane fuel cell performance

Preparation and Performance Study of PEK‐C‐OH/MWCNT‐COOH/Graphite Composite Bipolar Plates for PEMFCs With Improved Interface Properties

Electrical conductivity enhancement of chopped carbon fiber‐reinforced epoxy composite bipolar plate for proton exchange membrane fuel cells

Effect of carbon fiber length and graphene on carbon-polymer composite bipolar plate for PEMFC

High performance polyvinylidene fluoride/graphite/multi-walled carbon nanotubes composite bipolar plate for PEMFC with segregated conductive networks

Recent advances on materials and technologies of composite bipolar plate for proton exchange membrane fuel cell

Gradient Structured Composite Bipolar Plates for Proton Exchange Membrane Fuel Cells

Structure and Properties of Carboxylated Carbon Nanotubes@Expanded Graphite/Polyethersulfone Composite Bipolar Plates for PEM

Development of novel composite bipolar plates using surface‐modified conductive carbon filler materials for polymer electrolyte membrane fuel cells

Collective Enhancements on Thermal-Electrical and Mechanical Properties of Graphite-Based Composite Bipolar Plates through the Coupled Manipulations of Molding and Impregnation Pressures

Current status of research on composite bipolar plates for proton exchange membrane fuel cells (PEMFCs): nanofillers and structure optimization

High-performance polybenzoxazine based composites PEMFC bipolar plates with a multi-layer structure for surface enrichment of conductive phase

Researches on the MCMB/Graphite Composite for Bipolar Plate in Fuel Cell

Muti-Filler Composites Reinforced with Multiwalled Carbon Nanotubes and Chopped Carbon Fibers for the Bipolar Plate of Fuel Cells