Abstract:Conductive polymer composites (CPCs) exhibit favorable density and corrosion resistance for application as bipolar plate (BP) in proton exchange membrane fuel cell (PEMFC). However, achieving CPCs that combine the required level of electrical conductivity and mechanical strength is a challenge that has limited their application in PEMFC BPs. This study explored the potential of achieving CPC BPs with high electrical and mechanical performance by using carbon black (CB) as a secondary filler in graphite-polymer composites. Polypropylene (PP)/epoxy blend was selected as the matrix due to its good combination of strength and toughness as well as its potential to form a co-continuous morphology, which promotes the formation of more continuous conducting networks within the composite, leading to enhanced electrical performance. The PP/epoxy/graphite/CB composites were prepared by melt mixing in a Rheomixer at 190 °C and 60 rpm for 10 min, followed by compression molding at 200 °C and 6 metric tonnes for 10 min. The electrical conductivity of the composites increased from 49.26 Scm−1 to 90.34 Scm−1 (in-plane) and from 0.37 Scm−1 to 9.34 Scm−1 (through-plane) as the total filler content increased from 50 to 85 wt%. The flexural strength initially increased from 45.57 MPa at 50 wt% to 51.84 MPa at 60 wt% total filler content. Further increase in total filler content led to a decrease in flexural strength. The nanosize CB particles, used as a minor filler, filled the voids between the graphite particles, leading to the formation of more conducting pathways and higher electrical conductivities compared to the PP/epoxy/graphite composites without CB fillers. The PP/epoxy/graphite/CB composite with 80 wt% total filler content exhibited the most promising in-plane conductivity (88.5 Scm−1), through-plane conductivity (8.52 Scm−1), and flexural strength (28.53 MPa) for BP application.

Development of novel composite bipolar plates using surface‐modified conductive carbon filler materials for polymer electrolyte membrane fuel cells

Low filler and highly conductive composite bipolar plates with synergistic segregated structure for enhanced proton exchange membrane fuel cell performance

Electrical and mechanical properties of polypropylene/epoxy blend-graphite/carbon black composite for proton exchange membrane fuel cell bipolar plate

High performance polyvinylidene fluoride/graphite/multi-walled carbon nanotubes composite bipolar plate for PEMFC with segregated conductive networks

Achieving high electrochemical performance of PEMFCs with ultrathin and highly conductive graphite-resin composite bipolar plates

Preparation and properties of high performance nanocomposite bipolar plate for fuel cell

Recent advances on materials and technologies of composite bipolar plate for proton exchange membrane fuel cell

Electrical conductivity enhancement of chopped carbon fiber‐reinforced epoxy composite bipolar plate for proton exchange membrane fuel cells

Carbon/Carbon Composite Bipolar Plate for Proton Exchange Membrane Fuel Cells

Carbon Material-Reinforced Polymer Composites for Bipolar Plates in Polymer Electrolyte Membrane Fuel Cells

Collective Enhancements on Thermal-Electrical and Mechanical Properties of Graphite-Based Composite Bipolar Plates through the Coupled Manipulations of Molding and Impregnation Pressures

Structure and Properties of Carboxylated Carbon Nanotubes@Expanded Graphite/Polyethersulfone Composite Bipolar Plates for PEM

Bipolar plate design and fabrication using graphite reinforced composite laminate for proton exchange membrane fuel cells

A review on key factors influencing the electrical conductivity of proton exchange membrane fuel cell composite bipolar plates

Improved Performance of Composite Bipolar Plates for PEMFC Modified by Homogeneously Dispersed Multi-Walled Carbon Nanotube Networks Prepared by In Situ Chemical Deposition

Preparation and Performance Study of PEK‐C‐OH/MWCNT‐COOH/Graphite Composite Bipolar Plates for PEMFCs With Improved Interface Properties

High-performance polybenzoxazine based composites PEMFC bipolar plates with a multi-layer structure for surface enrichment of conductive phase

Gradient Structured Composite Bipolar Plates for Proton Exchange Membrane Fuel Cells

Effect of carbon fiber length and graphene on carbon-polymer composite bipolar plate for PEMFC

Simultaneous electrical and mechanical properties improvement for composite expanded graphite bipolar plate by incorporating surface-activated carbon black paving on the carbonized melamine foam skeleton