Abstract:The separation of oil in water and water in oil emulsions using the ceramic membranes with selective oil and water wettability has proven to be cost effective, less cumbersome and more efficient, compared to the conventional methods. In this work, a silicon carbide having hexagonal crystal structure (H-SiC) based ceramic membrane, exhibiting in-air superhydrophilicity and underwater superoleophobicity was fabricated for water passing oil-water emulsion separation. Initially silicon dioxide (SiO 2 ) was grown on the surface of H-SiC by thermal process to enhance the hydrophilicity, and further enhancement of hydrophilicity was introduced by amino-functionalizing H-SiC/SiO 2 using N 1 -(3-trimethoxysilylpropyl)diethylenetriamine (N-TMS-DETA). The amino-functionalized H-SiC/SiO 2 particles were deposited on porous alumina support surface and crosslinked via interfacial polymerization (IP) using Isophthaloyl chloride (IPC) cross-linker and ethylenediamine (EDA) to fabricate functional PA/H-SiC/SiO 2 @Alumina ceramic membrane for oil/water emuslion separation. The morphological, structural, elemental characterizations using FT-IR, XRD, FE-SEM, EDS, elemental mapping, and the wettability of PA/H-SiC/SiO 2 @Alumina ceramic membarne were carried out. The characterization results revealed the perfect deposition of functionalized H-SiC/SiO 2 on alumina support surface, and the contact angles of PA/H-SiC/SiO 2 @Alumina ceramic membrane surface in air-surface-water (θ WA ), and oil-surface-water (θ OW ) interfaces were 0° and ∼159.7° respectively. When PA/H-SiC/SiO 2 @Alumina ceramic membrane was used for the oil-water emulsion separation using dead-end filtration cell, an impressive separation efficiency of > 99% with a flux of around 312 L∙m −2 ∙h −1 was observed. The system was tested for the separation efficiency at different transmembrane pressures, oil concentration of oil-water emulsion, and the long term stabilty of the PA/H-SiC/SiO 2 @Alumina ceramic membrane.

Influence of additive contents on the properties of SiC ceramic membranes and their performance in oil‐water separation

Properties and performance of cordierite-bonded porous silicon carbide membrane prepared using waste fly ash and other oxide additives

Permeability Behavior and Wastewater Filtration Performance of Mullite Bonded Porous SiC Ceramic Membrane Prepared Using Coal Fly Ash as Sintering Additive

Lower-temperature preparation of SiC ceramic membrane using zeolite residue as sintering aid for oil-in-water separation

Preparation and Modification of Ceramic Membrane and Its Application in Oil/Water Wastewater Treatment

Ceramic Processing of Silicon Carbide Membranes with the Aid of Aluminum Nitrate Nonahydrate: Preparation, Characterization, and Performance

MgO-Al2O3-SiO2- ZrO2 System Ceramic Glass As Sintering Aids to Fabricate Al2O3 Ceramic Membrane with High Acid Corrosion Resistance

Silicon carbide ceramic membrane support sintered at 800 °C with low-temperature sintering aid

Preparation of high performance porous SiC ceramic membrane support using zeolite and alumina as sintering additives

Extrusion of Silicon Carbide Based Tubular Membrane Incorporated With Coal Fly Ash and Performance Evaluation in Water Treatment

Processing and microstructure-permeation properties of silica bonded silicon carbide ceramic membrane

Highly permeable silicon carbide-alumina ultrafiltration membranes for oil-in-water filtration produced with low-pressure chemical vapor deposition

Fabrication of Cost-Effective and Antifouling Al2O3-SiO2 Membrane for Efficient Oil Emulsion Separation

Tuning Microstructures and Separation Behaviors of Pure Silicon Carbide Membranes

Ultra-low temperature co-sintering of water glass (WG)-bonded silicon carbide ceramic membranes for oil-water separation

Fabrication of high-performance SiC ceramic membranes modified using in situ grown mullite whiskers and high-temperature filtration

Porous ceramic membranes from coal fly ash with addition of various pore-forming agents for oil-in-water emulsion separation

Facile fabrication of silicon carbide decorated ceramic membrane, engineered with selective surface wettability for highly efficient separation of oil-in-water emulsions

Fabrication of high-performance recrystallized silicon carbide ceramic membrane based on particle packing optimization

Oil-in-water emulsion separation: Fouling of alumina membranes with and without a silicon carbide deposition in constant flux filtration mode

One-step fabrication of asymmetric alumina ceramic membranes with tunable pore parameters for oil-water separation