Abstract:The relationship between the microstructures and cryogenic mechanical properties of the dissimilar laser welded joint between ultra-low carbon 5% Ni steel (SA645) and 304L stainless steel (AISI304L) was investigated to identify the crucial microstructural characteristics determining the low-temperature toughness of the joint. The microstructural constituents of the weld metal were changed by varying the laser beam offset towards AISI304L side. The low-temperature (-120 degrees C) impact energy of the weld without beam offset which consisted of full lath martensite was only 10.22 J. High-density tangled dislocations in lath martensite resulted in the embrittlement of the weld metal. With increase in the offset of laser beam, the cryogenic toughness of the weld with a dual microstructure of lath martensite and retained austenite (RA) was enhanced more than seven times (72.16 J). Areas with relatively low strain/stress caused by the strain-induced martensite transformation of RA were observed near the crack propagation path, which deflected crack propagation path and increased the resistance of crack propagation. However, the weld metal with a triplex microstructure of martensite, RA and delta-ferrite exhibited a lower cryogenic impact toughness (37.15 J) despite the high volume fraction of RA when the beam offset was high. The thermal stability of RA decreased significantly owing to the weakening of restrain effect of surrounding martensite. The improvement effect of RA on cryogenic toughness was attenuated due to the decreased thermal stability of RA and the occurrence of delta-ferrite. Research results indicate that the volume fraction and stability of RA and the existence of delta-ferrite with increasing the laser beam offset were confirmed as the pivotal microstructural factors determining the cryogenic impact toughness.

Microstructure Evolution and Cryogenic Impact Toughness Changes in Ce‐Containing Novel Cryogenic High‐Mn Austenitic Steel Weld Metals under Different Heat Inputs

Effect of Ce Content on Microstructure-Toughness Relationship in the Simulated Coarse-Grained Heat-Affected Zone of High-Strength Low-Alloy Steels

Improvement of impact toughness by microstructure refinement of simulated CGHAZ through enhancing welding heat input of low carbon Mo-V-Ti-N-B steel

Tailoring the Microstructure of Coarse-Grained HAZ in Steel for Large Heat Input Welding: Effect of Ti–Mg–Ce–V Inclusion/Precipitation Particles

Microstructure evolution and impact toughness variation for high strength steel multi-pass weld metals with various cooling rates

Precipitation behavior of carbides and cryogenic toughness in heat-affected zone of high-Mn twinning-induced plasticity steel welded joint

Effect of Tempering Heat Treatment on the Microstructure and Impact Toughness of a Ni-Cr-Mo-V Steel Weld Metal

Microstructure evolution and enhanced cryogenic toughness of laser welded dissimilar SA645/AISI304L joints via intercritical tempering

Effect of Ti content and martensite–austenite constituents on microstructure and mechanical property

Elucidating the heat input on CGHAZ microstructure and its irregular effect on impact toughness for a novel V-N microalloying weathering steel

Effect of grain size and segregation on the cryogenic toughness mechanism in heat-affected zone of high manganese steel

Crucial Microstructural Features to Determine the Mechanical Properties of Welded Joints in a Cu-Containing Low-Carbon Low-Alloy Steel After Postweld Heat Treatment

Effect of Heat Input on Austenite Reversion, Recrystallization, and Ensuing Impact Toughness in Simulated Intercritical Coarse‐Grained Heat Affected Zone of Medium Mn Steel

N-induced Microstructure Refinement and Toughness Improvement in the Coarse Grain Heat-Affected Zone of a Low Carbon Mo–V–Ti–B Steel Subjected to a High Heat Input Welding Thermal Cycle

Influence of banded ε-martensite and deformation twin on cryogenic toughness of Fe-Mn-xAl-C steel

Effect of Welding Processes with High Heat Input on the Microstructure and Toughness of Coarse-Grained Heat-Affected Zone of a High-Strength High-Toughness Steel

Pivotal Microstructural Characteristics to Determine the Cryogenic Impact Toughness of Dissimilar Joint Between SA645 and AISI304L Made by Autogenous Fiber Laser Welding

Effect of Initial Microstructure on the Toughness of Coarse-Grained Heat-Affected Zone in a Microalloyed Steel

Impact toughness and fracture behaviour of a lamellar structural Fe–Mn–Al–C cryogenic steel

Effect of heat input on toughness of coarse-grained heat-affected zone of an ultra low carbon acicular ferrite steel

EFFECTS OF HEAT INPUT ON THE MICROSTRUC-TURE AND IMPACT TOUGHNESS OF WELD METAL PROCESSED BY A NEW FLUXNOVEL FLUX CORED WIRE WELD