Abstract:The most important advantage of additive manufacturing by laser powder bed fusion (PBF-LB) technique is the ability to produce geometrically complex parts, but the problem is their rough surfaces, often difficult or inaccessible to finish by machining. Therefore, research to improve the reproducibility of the mechanical behavior of parts manufactured from aluminum alloy powders with as-built surfaces is of vital importance for the aerospace and automotive industries. Since local notches occurring on rough surfaces after the PBF-LB process are unavoidable, the way to solve this problem is to obtain as-built surfaces of the highest possible quality and to adapt a post-process heat treatment that increases the ductility and fracture toughness of the material. To this end, the present work focused on the study of the mechanical performance of AlSi7Mg0.6 samples with a rough as-built surface in the as-built state and after several variants of post-process heat treatment, combined with a detailed analysis of the microstructures corresponding to these states. Tensile samples built on a platform preheated to 100 °C, achieved a relative density of 99.85%, satisfactory surface quality, a relatively low level of residual stress and moderate crystallographic texture. Despite the rough surface, the samples under the as-built condition and after different variants of heat treatment (direct aging (DA), stress relieving (SR), and solution annealing followed by artificial aging (T6)), achieved tensile properties comparable to those reported in the literature for PBF-LB samples with machined surfaces. The resulting combinations of tensile properties of PBF-LB samples after different heat treatment variants were evaluated using the quality index (QI) commonly used to assess the quality of heat-treated Al-Si-Mg castings. It was found that the proposed T6 treatment provides the best combination of strength properties and ductility, compared to those obtained after both DA and SR, as well as after T6 treatment of high-quality castings, from the point of view of reducing the sensitivity of AlSi7Mg0.6 alloy to surface roughness.

Effect of heat treatment on fatigue crack growth performance of AlSi10Mg aluminum alloy submitted to LPBF

Failure analysis of fatigue crack propagation in specimens of AlSi10Mg aluminum alloy produced by L-PBF: Effect of different heat treatments

Fatigue behavior under variable amplitude loadings in AlSi10Mg alloy components produced by laser powder bed fusion

Effect of heat treatments on microstructure and mechanical properties of AlSi10Mg alloys fabricated by laser powder bed fusion

Effect of Surface Modification on the High Temperature Low Cycle Fatigue Performance of LPBF 316L Austenitic Steel

The Influence of Post-Treatment on Micropore Evolution and Mechanical Performance in AlSi10Mg Alloy Manufactured by Laser Powder Bed Fusion

Mechanical behavior and microstructure evolution of Al-Cu-Mg alloy produced by laser powder bed fusion: Effect of heat treatment

Tailoring heat treatment for AlSi7Mg0.6 parts with as-built surface generated by laser powder bed fusion to reduce surface roughness sensitivity

Low cycle fatigue response and fracture mechanism in a novel Al-3.5Si-0.5Mg-0.4Cu casting alloy

Effect of Heat Treatment on the Microstructure and Mechanical Properties of Al-7Si-0.7Mg-2.5Fe Processed by Laser Powder Bed Fusion

Fretting wear behavior on LPBF processed AlSi10Mg alloy for different heat treatment conditions

Fatigue analysis and heat treatment comparison of additively manufactured specimens from AlSi10Mg alloy

A multi-scale experimental investigation on fatigue crack propagation rate behavior of powder bed fusion-laser beam 316L stainless steel subjected to various heat treatments

Effect of Solution Treatment on the Microstructure and Fatigue Properties of 7050 Aluminum Alloy

Investigating post-processing impact on fatigue performance in LPBF Ti6Al4V with heat treatment, high pressure heat treatment, and dry electropolishing strategies

The influence of post-thermal treatments on microstructure and mechanical properties in A20X alloy fabricated through powder bed fusion

Environmentally-assisted Fatigue Crack Growth in AA7050-T73511 Al Alloy and AA2050-T84 Al-Cu-Li Alloy

Effect of Post-Processing Treatment on Fatigue Performance of Ti6Al4V Alloy Manufactured by Laser Powder Bed Fusion

Heat treatment of Al-Cu-Li-Sc-Zr alloy produced by laser powder bed fusion

Evolution of interphase stress over a crack propagation plane as a function of stress relief heat treatments in a PBF‐LB/M AlSi10Mg alloy

The Effect of Thermal Cycle on Hot Cracking Evolution and Formation Mechanism in Thin Wall, Single Layer, and Cubic Samples of High-Strength Al-Cu-Mg-Mn Alloys Fabricated by Laser Powder Bed Fusion